Industry Directory | Manufacturer
Oak-Mitsui specializes in the development and production of world class performance foils, Aluminum Bonded Copper, and FaradFlex� Buried Capacitance� materials.
Industry Directory | Distributor
Suppliers to the PCB Industry with a huge range of products including copper clad laminates, drill boards and consumables.
New Equipment | Fabrication Services
Aluminum PCB & Metal Core PCB & LED PCB Circuit board Aluminium PCB are metal-based, copper-clad laminates with a good heat dissipation function. Usually, Aluminium PCB is refer to LED PCB board, which is the most important part of LED display and l
To shield against emissions, there must be a barrier of an electrical conductive material. Shielding laminates provide an economical and effective solution to this problem. Most of our materials consist of a metal foil (usually, copper or aluminum)
Electronics Forum | Wed Sep 27 19:37:32 EDT 2000 | Dave F
Wolfgang is correct. Copper plating thickness of the via barrel walls is a key question you need to answer to troubleshoot this. Tenting is a red herring.
Electronics Forum | Wed Sep 27 17:24:08 EDT 2000 | Wolfgang Busko
Ashok: Plating thickness and ductility of the copper are things to look for. If it�s a crack where two layers are pressed together one possible cause could be bad process parameters while pressing these layers together at the PCB shop with the resul
Industry News | 2003-02-21 08:53:41.0
Gould Electronics Inc. said that all of its U.S. copper foil manufacturing will be consolidated at the company's Chandler, AZ facility by the end of the third quarter of 2003.
Industry News | 2003-03-12 09:03:48.0
Demand for the material, used in PCBs, is increasing because of folding mobile phones and other devices
Technical Library | 2018-08-15 17:27:28.0
Smartphones and tablets require very high flexibility and severe bending performance ability of the flexible printed circuits (FPCs) to fit into their thinner and smaller body designs. In these FPCs, the extraordinary highly flexible, treated rolled-annealed (RA) copper foils have recently used instead of regular RA foil and electro deposited foils. It is very important to measure the Young's moduli of these foils predicting the mechanical properties of FPCs such as capabilities of fatigue endurance, folding, and so on. Even though the manufacturers use IPC TM-650 2.4.18.3 test method for measuring Young's modulus of copper foils over many years, where Young's modulus is calculated from the stress–strain (S–S) curve, it is quite difficult to obtain the accurate Young's modulus of metal foils by this test method.
Technical Library | 2021-07-20 20:02:29.0
During the manufacturing of printed circuit boards (PCBs) for a Flight Project, it was found that a European manufacturer was building its boards to a European standard that had no requirement for copper wrap on the vias. The amount of copper wrap that was measured on coupons from the panel containing the boards of interest was less than the amount specified in IPC-6012 Rev B, Class 3. To help determine the reliability and usability of the boards, three sets of tests and a simulation were run. The test results, along with results of simulation and destructive physical analysis, are presented in this paper. The first experiment involved subjecting coupons from the panels supplied by the European manufacturer to thermal cycling. After 17 000 cycles, the test was stopped with no failures. A second set of accelerated tests involved comparing the thermal fatigue life of test samples made from FR4 and polyimide with varying amounts of copper wrap. Again, the testing did not reveal any failures. The third test involved using interconnect stress test coupons with through-hole vias and blind vias that were subjected to elevated temperatures to accelerate fatigue failures. While there were failures, as expected, the failures were at barrel cracks. In addition to the experiments, this paper also discusses the results of finite-element analysis using simulation software that was used to model plated-through holes under thermal stress using a steady-state analysis, also showing the main failure mode was barrel cracking. The tests show that although copper wrap was sought as a better alternative to butt joints between barrel plating and copper foil layers, manufacturability remains challenging and attempts to meet the requirements often result in features that reduce the reliability of the boards. Experimental and simulation work discussed in this paper indicate that the standard requirements for copper wrap are not contributing to the overall board reliability, although it should be added that a design with a butt joint is going to be a higher risk than a reduced copper wrap design. The study further shows that procurement requirements for wrap plating thickness from Class 3 to Class 2 would pose little risk to reliability (minimum 5 μm/0.197 mil for all via types).Experimental results corroborated by modeling indicate that the stress maxima are internal to the barrels rather than at the wrap location. In fact, the existence of Cu wrap was determined to have no appreciable effect on reliability.
Guillotine type V-cut PCB Cutting Machine Product Description 1. For internal strength generates during separation, Minimize it to value under 180uE ,to avoid solder crack or component damage 2. Able to separate edge of V-slot, minimum distance to
A Sustainable Alternative - Humitector cards are halogen-free and cobalt dichloride free. Visit https://www.clariant.com/solutions/products/2017/10/31/00/12/humitector-type-2-nonreversible-humidity-indicator-card?utm_source=CLRYouTube&utm_medium=Vi
Training Courses | | | IPC-6012 Specialist (CIS)
The Certified IPC-6012 Specialist (CIS) training covers design, fabrication and inspection of rigid printed boards.
Training Courses | | | IPC-600 Specialist (CIS)
The Certified IPC-600 Specialist (CIS) training targets quality assurance and acceptance of bare printed circuit boards.
Career Center | Erode, Tamilnadu India | Engineering
Professional Summary 3+ years of experience in the PCB CAM engineering Exposure to FRONTLINE GENESIS 2000 Having exposure in UCAM Exposure to Create, Array & Panelize it for manufacturability Experienced in Creating impedance cou
SMTnet Express, August 16, 2018, Subscribers: 31,259, Companies: 11,015, Users: 25,092 Reliable Young's Modulus Value of High Flexible, Treated Rolled Copper Foils Measured by Resonance Method Kazuki Kammuri, Atsushi Miki, Hiroki Takeuchi; JX
SMTnet Express, November 22, 2017, Subscribers: 31,034, Companies: 10,792, Users: 24,082 Factors Affecting the Adhesion of Thin Film Copper on Polyimide David Ciufo, Hsin-Yi Tsai and Michael J. Carmody; Intrinsiq Materials Inc. The use of copper
ORION Industries | http://orionindustries.com/pdfs/shielding.pdf
970639 Orion 4 sheets ORION INDUSTRIES INCORPORATED PCB-Shields A copper foil/polyester laminate was selectively die cut removing the copper foil from all edges of the piece
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/sonoscan/support/application-notes
Popcorn Crack 0299 PBGA Die Face Delaminations 0309 TSOP Die Cracks 0434 PQFPs Production Scanning 0759 TSOP Cracked Die 1009 PBGA Delaminations, Through Transmission 1011 PBGA Delaminations 1012 PBGA
