Industry Directory | Manufacturer
The exclusive supplier of SIPAD Solid Solder Deposit in North America and the only SIPAD Solid Solder Deposit (SSD) coating service bureau in the world.
Industry Directory | Manufacturer's Representative
Manufacturers Representatives for SMT Equipment and Materials serving Southern California and Baja, MX
S8, S10, S12 - 8, 10 or 12 top/bottom cooling zones. Heating System: Up to twelve groups of top and bottom forced hot air convection heating zones. Patented heating plates in each zone uniformly transfer heat to the PCBs using forced hot air con
E8, E10, E12 - 8, 10 or 12 top/bottom cooling zones. Heating System: Up to twelve groups of top and bottom forced hot air convection heating zones. Patented heating plates in each zone uniformly transfer heat to the PCBs using forced hot air con
Electronics Forum | Fri Jul 04 05:40:09 EDT 2008 | proy
Thanks, I'll give this a try. Peter
Electronics Forum | Fri Jul 04 00:36:25 EDT 2008 | shrek
Try a linear, very flat ramp rate on the order of 0.5 degrees celcius per second. I know this is hard to accomplish with a five zone, but try to lower the first couple of zones (the preheat zone), and then spike to reflow aggressively during your la
Used SMT Equipment | SMT Equipment
Features: 1. Heating system 1.1 Independent heating models are located with top and bottom with single hot air circulation in each zone. 1.2 All the heating zones are controlled by PLC through PLD, 1.3 Each zone is heated step by step, thus reducin
Used SMT Equipment | Soldering - Reflow
Vitronics 6622CC (Pb Free) Wave Soldering Machine Brand: Vitronics Model: 6622CC Vintage: 2001 Serial Number: 0103652201 LEADFREE unit Configured with Main Wave and Chip Wave Basic system according to General Specification (GS 235) CONTRO
Industry News | 2016-06-22 15:33:28.0
Based on its recent analysis of the surface mount technology (SMT) reflow soldering equipment market, Frost & Sullivan recognizes Heller Industries, Inc. with the 2016 Global Frost & Sullivan Award for Growth Excellence Leadership. Heller Industries has made remarkable improvements to its product and technology portfolios over the last 10 years to emerge a top participant in the SMT reflow soldering equipment market.
Industry News | 2017-09-16 02:29:39.0
Heller Industries has been awarded the 2017 Global Frost & Sullivan Company of the Year Award for its surface mount technology (SMT) soldering equipment that enables Industry 4.0. - the automation and data exchange in manufacturing technologies.
Parts & Supplies | Pick and Place/Feeders
SMT basic process components include: silk screen (or dispensing), placement (curing), reflow soldering, cleaning, testing, repair 1, silk screen: its role is to paste or patch solder paste printed on the PCB pad, the components f
Parts & Supplies | Soldering - Wave
Overseas Agent and Distributor Wanted ! Features : Spray Fiuxer: 1) Oriental motor drives the flux spraying system. Spraying speed is adjusted according to PCB board width and moving speed to ensure even spraying all time. 2) Durable “Meiji
Technical Library | 2020-11-24 23:01:04.0
The miniaturization trend is driving industry to adopting low standoff components or components in cavity. The cost reduction pressure is pushing telecommunication industry to combine assembly of components and electromagnetic shield in one single reflow process. As a result, the flux outgassing/drying is getting very difficult for devices due to poor venting channel. This resulted in insufficiently dried/burnt-off flux residue. For a properly formulated flux, the remaining flux activity posed no issue in a dried flux residue for no-clean process. However, when venting channel is blocked, not only solvents remain, but also activators could not be burnt off. The presence of solvents allows mobility of active ingredients and the associated corrosion, thus poses a major threat to the reliability. In this work, a new halogen-free no-clean SnAgCu solder paste, 33-76-1, has been developed. This solder paste exhibited SIR value above the IPC spec 100 MΩ without any dendrite formation, even with a wet flux residue on the comb pattern. The wet flux residue was caused by covering the comb pattern with 10 mm × 10 mm glass slide during reflow and SIR testing in order to mimic the poorly vented low standoff components. The paste 33-76-1 also showed very good SMT assembly performance, including voiding of QFN and HIP resistance. The wetting ability of paste 33-76-1 was very good under nitrogen. For air reflow, 33-76-1 still matched paste C which is widely accepted by industry for air reflow process. The above good performance on both non-corrosivity with wet flux residue and robust SMT process can only be accomplished through a breakthrough in flux technology.
Technical Library | 2015-02-05 20:25:41.0
In the past 20 yrs the solvent industry has gone through a great deal of change. In the early 1990s, CFC-113 and 1,1,1-trichloroethane were the workhorses of the industry. The Montreal Protocol to phase-out substances that deplete the Earth's protective Ozone Layer was implemented in the mid 1990s. After phase-out of the CFC solvents, the solvent industry fragmented to a variety of cleaning solutions. The electronics industry was a large user of CFC solvents and many of these applications changed to aqueous based cleaners (...) But those alternatives are now facing various problems: e.g. aqueous based cleaners use a lot of energy, require long drying times, use equipment that requires frequent maintenance, and require a large footprint; no-clean fluxes leave flux residues; and trichloroethylene and n-propyl bromide have toxicity issues. In response to these serious issues newer solvents and blends are being introduced in the marketplace
DescriptionThe Electrovert® Electra™ is an advanced, meticulously engineered wave soldering system designed for high-mass and high-volume manufacturers. Although intended for maximum throughput requirements, the Electra also offers maximum process fl
Events Calendar | Sun Sep 27 00:00:00 EDT 2020 - Thu Oct 01 00:00:00 EDT 2020 | Rosemont, Illinois USA
SMTA International 2020 Conference & Exhibition
Career Center | Raleigh, North Carolina USA | Engineering
Title: SMT PROCESS ENGINEER Salary: 70k-80k max rate with great benefits Job Description: ESSENTIAL DUTIES & RESPONSIBILITIES To perform this job successfully, an individual must be able to perform each essential duty satisfactorily, plus w
Career Center | Riyadh 11623, Philippines | Engineering,Maintenance,Production
PROFESSIONAL EXPERIENCE: Connected in the field of manufacturing/electronics industry experienced in the line, Through Hole and Surface Mount Technology, worked on various Fuji Machines Universal model, such as: CP 643E chip shooter QP 242E chip mou
Career Center | tulsa, Oklahoma | Engineering
Printed Circuit Assembly Process Engineer. Seeking a position in a high-technology operation, utilizing my background supporting a progressive and growth-oriented organization. Offering the technical experience, expertise, and skills gained during th
| http://etasmt.com/cc?ID=te_news_bulletin,24761&url=_print
Reflow machine FLUX CONDENSER / COOLING MODULE-News-Reflow oven,SMT Reflow Soldering Oven-cmsadmin Reflow oven,SMT Reflow Soldering Oven 当前位置: Home >> News
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/products/efd-products/fluxplus-paste-flux
. WS flux residue is corrosive and should be removed as soon as possible after reflow to avoid damage to your assembly. Maximum safe time before cleaning is product dependent
.gif)
