New Equipment | Solder Paste Stencils
Simplify and Speed Up QFN and LGA device rework. StencilMate™ leadless device rework stencils make the process of reworking leadless devices such as QFNs and LGAs simple and fast. These adhesive-backed poyimide stencils are placed on to the bottom o
New Equipment | Solder Paste Stencils
Based on its long work on BGA rework and repair process and its in-house capability to produce metal stencils BEST can provide for you a timely, cost-effective solution for printing on to components for MOST rework systems. Our templates for printing
Electronics Forum | Fri Jul 27 09:47:20 EDT 2018 | davef
Adding to Rob's suggestions ... One of the theories about voiding in thermal / ground pads of BTC is: Solder starts melting at the edge of the pad and moves inward towards the center of the solder mass. This traps flux volatilizes. So, there needs t
Electronics Forum | Tue Jul 19 18:40:41 EDT 2022 | emeto
Nitrogen is helping voids, so if you have specific parts that are prone to voids, you might start seeing more voids. Joints will probably look a little dull in comparison and this might affect your existing AOI programs.
Industry News | 2018-04-11 20:04:01.0
SMTA Europe announces Session 3 Technical Program on Advanced Test Methods at the “Electronics in Harsh Environments Conference” to be held in Amsterdam, Netherlands, on April 25th, 2018.
Industry News | 2011-09-14 12:04:43.0
The SMTA announced a session on QFN Assembly and Reliability will take place on Tuesday, October 18 during their annual conference, SMTA International, in Ft. Worth, Texas. Andrew Mawer of Freescale Semiconductor will chair the session and Viswam Puligandla, Ph.D., Nokia (Retired) will co-chair.
Technical Library | 2017-08-17 12:28:30.0
At SMT assembly, flux outgassing/drying is difficult for devices with poor venting channel, and resulted in insufficiently dried/burnt-off flux residue for no-clean process. Examples including: Large low stand-off components such as QFN, LGA Components covered under electromagnetic shield which has either no or few venting holes Components assembled within cavity of board Any other devices with small open space around solder joints
Technical Library | 2013-02-08 22:56:47.0
Solder voiding is present in the majority solder joints and is generally accepted when the voids are small and the total void content is minimal. X-ray methods are the predominate method for solder void analysis but this method can be quite subjective for non grid array components due to the two dimensional aspects of X-ray images and software limitations. A novel method of making a copper "sandwich" to simulate under lead and under component environs during reflow has been developed and is discussed in detail. This method has enabled quantitative solder paste void analysis for lead free and specialty paste development and process refinement. Profile and paste storage effects on voiding are discussed. Additionally an optimal design and material selection from a solder void standpoint for a heat spreader on a BCC (Bumpered Chip Carrier) has been developed and is discussed.
· What is the difference between SMT vacuum reflow soldering machine and ordinary reflow soldering machine? · What problems can be solved by smt vacuum reflow soldering machine? · What is the basic principle of vacuum reflow machine? · Ho
BGA component installation demo with the Shuttle Star SV560 that has the Side View Camera option.
Training Courses | | | PCB Rework and Hand Soldering Courses
The PCB rework and hand soldering courses courses cover techniques of rework and repair of PCBs, BGAs and other electronics assemblies, and teach fundamentals of soldering of electronics assemblies.
Training Courses | | | PCB Rework and Hand Soldering Courses
The PCB rework and hand soldering courses courses cover techniques of rework and repair of PCBs, BGAs and other electronics assemblies, and teach fundamentals of soldering of electronics assemblies.
Events Calendar | Mon Dec 02 00:00:00 EST 2019 - Mon Dec 02 00:00:00 EST 2019 | ,
Webinar: QFN/LGA Design, Assembly Process Issues & Reliability Failures
Events Calendar | Wed Mar 07 00:00:00 EST 2018 - Wed Mar 07 00:00:00 EST 2018 | ,
Solder Paste Qualification Testing - SMTA Webinar
Career Center | Oldsmar, Florida USA | Maintenance,Production
Job Description: • Uses microscope to verify correct part placement and orientation, manually align parts before soldering and perform post re-flow inspection and touch-up. • Able to identify and touch up poor wetted solder joints, solder voids / i
Career Center | banaglore, karnataka India | Maintenance,Production,Quality Control,Technical Support
tel u later
Heller Industries Inc. | https://hellerindustries.com/parts/591823/
? Reflow Soldering Problems Overview Causes & Defects – Reflow Soldering Solder Ball Defects Opensor Insufficient Solder Wicking Defects Tombstoning PCB Soldering PCB Bridging Defects PCB Dewetting PCB Nonwetting Circuit Board Voids PCB Delamination
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/efd/resource-center/solder-glossary-of-terms
temperature joints. T Tackiness Ability of solder paste to hold surface-mount components in place after placement. Tensile Strength Characteristic of a material that describes its resistance to fracture when the material is under tension. Through hole A
