Industry Directory | Training Provider / Events Organizer / Association / Non-Profit
The SMTA membership is a network of professionals who build skills, share practical experience and develop solutions in electronic assembly technologies and related business operations.
Industry Directory | Manufacturer
IRC has been a leader in resistor technology, including the industry's comprehensive range of current sense resistors, precision discrete and networks, integrated passive components, and specialized power resistors.
New Equipment | Board Handling - Storage
Low Cost PCB Transport Racks for up to 50 Printed Circuit Cards of up to 18" (460 mm) deep are made of antistatic material. Side plates can be adjusted from 5.9" (150mm) to 13" (330 mm).Use in TKD Inserter. Specifications: Size: 15.7"D X 18"W X 2
New Equipment | Board Handling - Storage
Flat PCB holding trays are designed to hold up to 25 PCBs for storage and transport at manual workstations. These trays will hold virtually any PCB size. As with all transport racks, these are made of antistatic material. Specifications: Size: 17
Electronics Forum | Wed Feb 23 02:20:09 EST 2000 | Roni H.
Hi, I need a wear resistance PCB finishing over bare copper (If exist!), the surface have a moving part which slides over it and bare copper as a surface is not good enough. I'll apprechiate any information. Thanks Roni
Electronics Forum | Wed Feb 23 02:20:09 EST 2000 | Roni H.
Hi, I need a wear resistance PCB finishing over bare copper (If exist!), the surface have a moving part which slides over it and bare copper as a surface is not good enough. I'll apprechiate any information. Thanks Roni
Used SMT Equipment | In-Circuit Testers
Megger DET14C Clamp-on Ground Resistance Testers The DET14C and DET24C are advanced clamp-on ground resistance testers that set new standards in terms of access, performance, features, simplicity of operation and safety. These units are designe
Used SMT Equipment | In-Circuit Testers
Megger DET24C Clamp-on Ground Resistance Testers The DET14C and DET24C are advanced clamp-on ground resistance testers that set new standards in terms of access, performance, features, simplicity of operation and safety. These units are designe
Industry News | 2003-03-26 08:25:40.0
The QVE00033 transmissive switch's small size, surface mount package and performance make it ideal for noncontact switching applications in disk drives, card detectors, mise and trackballs.
Industry News | 2003-03-24 09:46:41.0
Will feature a number of new technologies of interest to fabricators in printed circuit materials, laminate materials, polymer thick films and, most notably, its newest product line of embedded passive materials, DuPont Interra�.
Parts & Supplies | Assembly Accessories
TEST PCB LP3 ..00359534-01 Tester PEL-2002A Push pull tester NK-500 Neon lamp tester SX-C Test Probes (Universal Probe) TL20 Probes Connector Test Point temp (Male) SMPW-K-M. DIP TESTER DS-10
Parts & Supplies | Assembly Accessories
TEST PCB LP3 ..00359534-01 Tester PEL-2002A Push pull tester NK-500 Neon lamp tester SX-C Test Probes (Universal Probe) TL20 Probes Connector Test Point temp (Male) SMPW-K-M. DIP TESTER DS-10
Technical Library | 2007-02-01 09:36:26.0
Purpose: Compare the Surface Insulation Resistance of reworked BGA Test samples made with standard solder balls using a flux only reattachment and samples made including the StencilQuik™ product from Best Inc. with solder balls using a flux only reattachment.
Technical Library | 2023-01-10 20:15:42.0
Over the past years there has been consistent growth in the use of electroless nickel / immersion gold (ENIG) as a final finish. The finish is now frequently being used for PBGA, CSP, QFP and COB and more recently gathered considerable interest as a low cost under-bump metallization for flip chip bumping application. One of the largest users for this finish has been the telecommunication industry, were millions of square meters of PCBs with ENIG have been successfully used. The nickel layer offers advantages such as multiple soldering cycles and hand reworks without copper dissolution being a factor. The nickel also acts as a reinforcement to improve through-hole and blind micro via thermal integrity. In addition the nickel layer offers advantages such as co-planarity, Al-wire bondability and the use as contact surface for keypads or contact switching. Especially those pads, which are not covered by solder need a protective coating in corrosive environment – such as high humidity or pollutant gas.
ACI Technologies Inc. (ACI) is a scientific research corporation dedicated to the advancement of electronics manufacturing processes and materials for The Department of Defense and industry. This video provides an overview of our commercial service
https://www.ascen.ltd/Products/conformal_coating_equipment//580.html PCB Conformal coating machine is used to paint conformal coating onto full LED panel to avoid PCB moisture,sault and static.It can be full panel conformal coating or selective coati
Training Courses | | | IPC-600 Specialist (CIS)
The Certified IPC-600 Specialist (CIS) training targets quality assurance and acceptance of bare printed circuit boards.
Training Courses | | | Other Courses
Other courses related to electronics manufacturing and assembly
Events Calendar | Thu Apr 08 00:00:00 EDT 2021 - Thu Apr 08 00:00:00 EDT 2021 | ,
Huntsville Chapter Technical Meeting: Evaluating Conformal Coatings
Events Calendar | Wed Oct 20 00:00:00 EDT 2021 - Wed Oct 20 00:00:00 EDT 2021 | ,
Penang Chapter Virtual Vendor & Technical Day
Career Center | Phoenix, Arizona | Engineering,Management,Production,Quality Control,Research and Development,Sales/Marketing,Technical Support
• Highly motivated, solution oriented professional with proven record synergizing scientific, engineering, and business administration backgrounds to drive and sustain customer satisfaction and long term improvements. • Articulate communicator that a
Career Center | Shen Zhen, China | Management,Sales/Marketing
Working in GLORYPCB for 10 years.knowing electronic supply chain very well. especially for PCB PCBA assembly and other Electronic Manufacturing Service.Glorypcb is a professional electronic manufacturer located in Shenzhen with three facilities.offe
Developments in Fine Line Resist Stripping Developments in Fine Line Resist Stripping In this paper, the concept for the next generation of resist stripper solutions is introduced, with specific emphasis upon development of new solutions targeted
| https://www.eptac.com/faqs/ask-helena-leo/ask/multiple-wash-steps-affecting-resistance-characteristics
Multiple Wash Steps Affecting Resistance Characteristics - EPTAC - Train. Work Smarter. Succeed Looking for solder training standards, manuals, kits, and more
Surface Mount Technology Association (SMTA) | https://www.smta.org/icsr/speaker_forms/Paper-Format-Requirements.doc
side reflow Ensure a robust surface finish that remains solderable after 2 heat cycles. In circuit test strain limits could be larger with thicker boards. ICT stress must be minimal to prevent BGA fracture Ensure low contact resistance on test points
The SMTA membership is a network of professionals who build skills, share practical experience and develop solutions in electronic assembly technologies and related business operations.
Training Provider / Events Organizer / Association / Non-Profit
6600 City W Pkwy
Eden Prairie, MN USA
Phone: 952-920-7682
winsouce.jpg)
.gif)