Ersa HOTFLOW 4/20 Reflow Oven Working width: 45-560 mm Process length: 5,920 mm Heated length: 3,805 mm Cooling length: 2,115 mm Weight appr. 2,600 kg Dimension: 6,600x1,410x1,350 mm Ersa HOTFLOW 4/20 Reflow Oven Ersa HOTFLOW 4/20 Reflow Oven
High temperature Pt-sensors for emission- control for both commercial as industrial engines. Focused on the GDI-engines and OBD - applications
Electronics Forum | Wed Sep 03 07:39:19 EDT 2008 | pjc
You may not be getting enough exhaust pull, so the cooling modules over temp. Try swapping blower motors to isolate that before buying one. STANDARD AIR OPERATION: - Load-end: 150 cfm (255 m3/hr) at the 4� (102 mm) stack (minimum requirement) - Unlo
Electronics Forum | Wed Feb 08 03:35:58 EST 2006 | GS
100�C) the moisture changes in vapour/gas generating an internal pressure causing in the worst case damages like internal planes delamination, popcorn effects, degassing, ecc. So you can understand why before reflow it could be necessary to backe and
Used SMT Equipment | Soldering - Reflow
Heating zones: 5 Cooling zones: 2 Total heating length: 66 in. Total cooling length: 26 in. Total process length: 127 in. Total on /off load length: 11 in. Overall system length: 138.5 in. Overall system width: 52 in. Overall system height: 5
Used SMT Equipment | Soldering - Reflow
Desk Reflow Oven Features: Cost-effective Desk Reflow Oven utilizes forced air convection heating technology and PC software interface to make an accurate temperature profile quickly and easily. T200 is a fine temperature profile model wit
Industry News | 2021-08-29 21:11:45.0
A compressor is a kind of driven fluid machinery that elevates low-pressure gas to high pressure. It is the heart of the refrigeration system. It inhales refrigerant gas with low temperature and low pressure from the suction pipe, compresses the piston driven by the motor, and then emits refrigerant gas with high temperature and high pressure to the exhaust pipe to provide power for the refrigeration cycle.
Industry News | 2021-12-13 20:23:11.0
During the use of your air compressor, there could be tricky oil separator burning failures. So this article will tell you the causes and solutions as well as some cases.
Parts & Supplies | Pick and Place/Feeders
JUKI 40068169 SOLENOID VALVE V FUJINTAI TECHNOLOGY CO.,LTD JUKI 40068170 SOLENOID VALVE B www.fujintai.com JUKI 40068171 EXHAUST FILTER FUJINTAI TECHNOLOGY CO.,LTD JUKI 40068178 VACUUM_PUMP_MAINTENANCE_KIT www.fujintai.com JUKI 40068308 SET SCREW
.jpg)
Parts & Supplies | Pick and Place/Feeders
CYBEROPTICS laser/CYBEROPTICS camera:JUKI laser(570/620/730/740/750/760/2010/2020/2030/2040/2050/2060/2070/2080/KJ-01/KJ-02//FX-1/FX-2/FX-3/3020R/JX-100 laser unit),YAMAHA laser,SAMSUNG laser,TENRYU laser,PHILIPS(ASSEMBLEON) FCM PPU laser,Autotronik
Technical Library | 2019-05-06 23:04:05.0
The temperature and humidity test chamber simulate the temperature and humidity, so there are a lot of things customers shoud notice in the process of use, although there is detailed instruction when purchasing the equipment. But some users just know how the device works and start using it. This is very easy to cause problems in the use of the equipment, so Symor intends to describe the safety details during the use of temperature and humidity chamber. 1. Before the test, determine if the sample contains flammable and explosive substances to avoid combustion or explosion during the test. Of course, also make sure there is no flammable and explosive material around the test equipment, otherwise it may cause fire and other accidents. 2, Do not open the chamber door to operate during the experiment, or the gas in the studio may cause the operator to burn and so on. 3. At the end of the test or at the time of regular cleaning of the test chamber, power off the equipment to avoid electrocution accidents. Also, when cutting off the equipment power, pull the power cord to pull out the plug, otherwise it may lead to a rupture of the power cord and so on. You can contact manufacturers if there are some places you donnot understand, do not dismantle and repair the temperature and humidity test chamber without authorization, otherwise it may lead to more serious problems.
Technical Library | 2019-05-08 00:04:49.0
It is necessary to know there are some faults that cannot be entirely avoided during the use of temperature and humidity test chamber, but how to deal with them in time is a problem that needs to be paid attention to.Here mainly explain the temperature and humidity test chamber compressor in the reason for the water, and how to deal with it. Reason: water comes from air, because there is always water in the air, known as humidity, which is compressed into supersaturated air and then analyzed to become liquid. The oil comes from the lubrication system of the compressor, possibly because the wear clearance of the mechanism increases, and the lubricating oil will escape into the cylinder. Solution: after the compressor is removed from the temperature and humidity test chamber, with a larger gas storage tank, the oil and water will naturally settle down to the bottom of the jar, and we need to discharge regularly to reduce the oil and water content in the compressed air. Of course, you can also use filters and other things to further reduce the content of oil and water. if you need to know more details about climatic chamber, keep an eye on our website www.climatechambers.com
DescriptionThe Electrovert® Electra™ is an advanced, meticulously engineered wave soldering system designed for high-mass and high-volume manufacturers. Although intended for maximum throughput requirements, the Electra also offers maximum process fl
Article Return to Front Page A Low Temperature Alte
Article Return to Front Page A Low Temperature Alte
Surface Mount Technology Association (SMTA) | https://www.smta.org/knowledge/proceedings_abstract.cfm?PROC_ID=5027
Effects of Cl2, NO2, Rh and Temperature on Accelerated Silver and Copper Corrosion in Mixed Flowing Gas Test 中文 MEMBERS LOGIN Membership Become a Member
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/adhesive-dispensing-systems/additional-filter-product-subtype/temperature-controls?con=t&page=13
Temperature Controllers For Production Flexibility And Efficiency | Nordson Adhesive Dispensing Systems Adhesive Dispensing Systems Corporate | Global Directory
.gif)
