33 aqueous technologies ultrasonic stencil washer jmw results

Electronics Forum: aqueous technologies ultrasonic stencil washer jmw (Page 1 of 4)

Small board washer needed

Electronics Forum | Thu Jul 26 13:08:59 EDT 2007 | Mike Konrad

The best method of cleaning misprinted boards is with a stencil cleaner. I would not recommend the use of a spray-in-air system for misprints. Spray systems can cause solder paste to become embedded into vias and under components (if double sided).

Recommendations for ultrasonic cleaning solution

Electronics Forum | Tue Jul 10 18:03:49 EDT 2001 | pzohbon

Does anyone have a recommendation for a cleaning solution used in an ultrasonic cleaner for cleaning RMA solder paste off stencils and adhesive off pcb boards. I am going to be evaluating Armakleen 2001, Zestron Vigon SC 200, and Aqueous Technologies

Re: Ultrasonic stencil cleaner

Electronics Forum | Mon Apr 13 19:35:11 EDT 1998 | Mike Konrad

Aqueous Technologies manufacturers a "no-frills" stencil cleaning system. The Model designed to handle stencils up to 24" x 24" is available for under $ 10K. This system is, however, not ultrasonic, rather spray-in-air. If you desire information, c

Ultrasonic stencil cleaners

Electronics Forum | Fri Oct 12 14:32:52 EDT 2001 | Mike Konrad

Hi, Maybe Yes� Maybe No� Actually, it most likely is acceptable to clean assembled boards in an ultrasonic cleaning system (40 kHz). There are some concerns in some circles about possible damage to wire bonds in components. There have been publi

Researching stencil cleaners

Electronics Forum | Tue Mar 27 15:15:32 EST 2001 | Mike Konrad

SmartSonic states that they will not sell their 440R chemistry unless it will be used with their machines. But to answer your question, the following manufacturers make ultrasonic stencil cleaners compatible with 440R and many other chemistries. Aq

PCB Cleaner/washer suggestions

Electronics Forum | Wed Oct 06 11:52:45 EDT 2004 | Mike Konrad

You state that you need a washer for �pcb washer/cleaner for misprints etc� Is it only for misprints or is it also for post-reflow de-fluxing? I would not suggest that you utilize one machine for both applications. Misprints should always be cle

Stencil Cleaners

Electronics Forum | Tue Apr 04 11:43:06 EDT 2006 | Mike Konrad

Here's a "flameless" reply... I�ll allow others to recommend� Here is a list of the �usual suspects�: Aqueous Technologies Batch and inline de-fluxers Ultrasonic stencil cleaning systems De-fluxing and stencil cleaning chemicals www.aqueoustech.co

Cheapest But Effective Stencil Cleaner?

Electronics Forum | Mon Aug 25 19:27:11 EDT 2008 | Mike Konrad

There are a number of �low cost� stencil cleaners available. I am a manufacturer of one but I'll list a variety and let the others provide editorial on which is best. Basically, there are three technologies, manual cleaning (solvents and wipes), ul

Stencil Washing

Electronics Forum | Sat Feb 12 20:02:04 EST 2005 | Mike Konrad

As for specific recommendations, I�ll defer to �real users�. But here are the usual suspects: Aqueous Technologies http://www.aqueoustech.com (909) 944-7771 Ultrasonic Smart Sonic http://www.smartsonic.com (818) 610-7900 Ultrasonic PMR http://www

UltraSonic cleaning machine

Electronics Forum | Thu Sep 26 14:03:55 EDT 2002 | Randy V

There are allot of issue to washing that need to be considered before you purchase a washer. But to answer your question regarding ultrasonic cleaning: 1. Ultrasonics with the correct frequency will not damage most components. Washing in general can