Electronics Forum: front door open (Page 1 of 15)

QFP IC open solder

Electronics Forum | Mon Sep 23 03:12:01 EDT 2002 | surachai

We encounter this problem also , I know that it 's acceptable per IPC standard but sometime it fail at ICT and FCT , then this problem should be prevent , we found it with QFP 16 mil pitch and the defect looklike negative wetting at the front of lead

Fuji cp6 servo amp alarm

Electronics Forum | Fri Sep 18 03:02:07 EDT 2015 | linux

Hello everyone. Need urgent help with our cp6, when front door is open servo amp alarm comes up, this error will clear using the reset button. Has anyone any idea how I would go about fixing this issue.

Homebrew vapour phase...?

Electronics Forum | Sat Jun 19 03:11:25 EDT 2010 | sarason

I have used the Quick ? from I don't remember what company. But it was a smallish machine ie about the size of a washing machine. The heat/cool cycle was about 30 to 45 minutes. every thing had to be properly sealed or you would loose vapour, this va

Strange problem with Fuji IP1 stopping

Electronics Forum | Thu Mar 30 13:27:53 EST 2006 | bvdb

Just before Christmas we bought a used Fuji IP1 cheap. It took us a while but it's been working great for about a month. Yesterday the IP1 stopped after completing a board but before exiting the board out the conveyer. No error message, no alarm be

MPM AP25 Print Repeatability Problem

Electronics Forum | Wed Sep 27 17:49:41 EDT 2006 | SWAG

Open the rear door that has the cooling fans on it. Look at the wiper blade regulator, look toward the front of the machine about 8" or so and to then left 3"or 4". There should be a lexan cover/box over the board that has this pot. on it. If stil

Panasert MPA 80 NM 2523

Electronics Forum | Wed Mar 13 17:17:42 EDT 2013 | isd_jwendell

I don't know your machine, but on mine the interlock is the large access door. It's done so that you cannot open the cover while running, but it also checks for a closed door at startup due to head homing sequence. Yours may be similar in that it won

QUAD 4C motor error #5

Electronics Forum | Thu Aug 29 14:20:17 EDT 2013 | nophsem

Thanks for the response bobpan! LED's on the driver cards work well (green with doors closed and both red&green on with door open), and I don't use the carts. The head doesn't move after power on and inmediately you can listen alarm.

Meridian 1020P servo wont start

Electronics Forum | Thu Jun 26 05:07:19 EDT 2014 | bobpan

On the older machines if the z-axis has springs on them sometimes they get weak and when you open the door the z will not stay up. Before closing the door manually push the z up if they are dropping down then enable the motor power. If this is the ca

QSP2-PLUS

Electronics Forum | Wed Sep 02 14:58:35 EDT 2015 | derrikf

Steve, Does said phenomena occur at a particular time? Or is it seemingly random? What sensors are you referring to? The door sensors, (as in you have the doors open and the gantries move)?

Cure Ovens and Cycle Interuption

Electronics Forum | Fri Dec 17 13:23:15 EST 1999 | Chris

I have an underfill material which takes 6 hours to cure. It works great, better than any other underfill I have ever used. A vertical cure oven is too expensive. I am currently using batch style ovens and opening the oven door as additional produ

  1 2 3 4 5 6 7 8 9 10 Next

front door open searches for Companies, Equipment, Machines, Suppliers & Information

Global manufacturing solutions provider

High Precision Fluid Dispensers
Software for SMT

Best Reflow Oven
Best SMT Reflow Oven

World's Best Reflow Oven Customizable for Unique Applications
PCB separator

Internet marketing services for manufacturing companies