Electronics Forum: hot motor (Page 1 of 2)

Philips Orion showing a L049 motor error.

Electronics Forum | Fri Sep 11 12:44:16 EDT 2015 | simons

Our Philips Orion shows a L049 motor error immediately after we turn it on. Note that the Y axis servomotor was very hot prior to the last shutdown. Is this a problem with the motor or one of the boards?

electrovert Omniflow 10

Electronics Forum | Tue May 07 13:11:33 EDT 2013 | emeto

Hi Hege, there is insulation, which when you look at looks pretty stable.I suspect that there is more heat transfer through the shaft from the propeller to the motor. However when I touch the motor it is not really hot, so I am confused what really

Mydata TP11 UFP hardware initiation failure

Electronics Forum | Wed Jul 26 16:08:29 EDT 2006 | ev

My focus has moved to the X motor itself. The one common factor in this paricular problem has been the time of year. The day was a particularly hot day with high humidity. Even though there is a "Xfan" connection on the PIAB board I do not believe th

MyData A12 tool tip damage

Electronics Forum | Wed Jun 27 11:58:42 EDT 2012 | cyber_wolf

Your tool tips are being damaged because the small x-motor is not engaging when the head is picking parts. When this happens the head overshoots and you bang the tips on the mag springs. Directly after a tip gets damaged go into the service program a

treiber washer question

Electronics Forum | Tue Aug 01 15:02:06 EDT 2006 | BillB

Had a Treiber in a past live. Had a standard air knife in the first section and then a turbine blower with a stainless steel air knife with about 15-horse motor. Had some problems with bearing on the turbine Make sure the exhaust hot air doesn't con

The story so far!

Electronics Forum | Mon Dec 04 18:29:47 EST 2006 | SWAG

Some production problems we've faced: 1) Delamination; 2) Reflow fixture distortion; 3) Obsolete parts; 4) Failure of blower motor bearings in older reflow ovens; 5) Poor toe fillets with miniSOTs on thicker PCB's; 6) Lack of updated component data s

Wave soldering profiling

Electronics Forum | Fri May 07 17:38:00 EDT 2004 | bruce @ knoll

I will try that next. I did speed up the wave pump motor with a larger pully(20% more speed) This was done at the time to try to increase the size of the wave because I had component leeds touching the wave pot as they passed by. Due to the wave high

wave solder machine

Electronics Forum | Tue May 17 10:11:54 EDT 2005 | russ

I would use a foam fluxer since spraying rosin will make the stickiest nastiest mess you can imagine. 18 layer board huh? You will want convection preheat, both top and bottom preheaters, preheat tunnel of at least 4-5', a chip wave, laminar flow w

MyData A12 tool tip damage

Electronics Forum | Wed Jun 27 03:43:24 EDT 2012 | allgood

Very interesting - esp that you have removed the temperature variable by being airconditioned. We defeinitely do not get strikes at 74 but do at 80 - but also we dont start the machine when its 80, that is the afternoon tempertaure on a rare hot day

Flason SMT Products

Electronics Forum | Wed Oct 03 23:42:32 EDT 2018 | gaintstar

SMT Reflow Oven Factory http://www.flason-smt.com/product/SMT-Reflow-Oven-Factory.html Introduction of SMT Reflow Oven Factory: 1. Windows XP platform, user friendly interface and easily swap between bilingual of English & Chinese. 2. Digital contr

  1 2 Next

hot motor searches for Companies, Equipment, Machines, Suppliers & Information