Electronics Forum: mpm cover door open (Page 1 of 2)

MPM AP25 Print Repeatability Problem

Electronics Forum | Wed Sep 27 17:49:41 EDT 2006 | SWAG

Open the rear door that has the cooling fans on it. Look at the wiper blade regulator, look toward the front of the machine about 8" or so and to then left 3"or 4". There should be a lexan cover/box over the board that has this pot. on it. If stil

Panasert MPA 80 NM 2523

Electronics Forum | Wed Mar 13 17:17:42 EDT 2013 | isd_jwendell

I don't know your machine, but on mine the interlock is the large access door. It's done so that you cannot open the cover while running, but it also checks for a closed door at startup due to head homing sequence. Yours may be similar in that it won

QUAD 4C motor error #5

Electronics Forum | Thu Aug 29 05:01:38 EDT 2013 | bobpan

Motor Error 5 is usually an interlock error. Take off the rear right cover and look at the red and green led's on the driver cards. If they are both lit....you have a door open or if you have carts....a feeder base switch is up. Good Luck

CSM84 doorway ?

Electronics Forum | Wed Feb 28 16:46:08 EST 2007 | jmelson

Philips is out of this business. They spun off the SMT business as Assembleon America. Their site is partially closed, and I don't know what hoops you have to jump through to become a member. The open part of their site gives no result when you se

Can anyone help me get this MPM AP27 going?

Electronics Forum | Mon Sep 28 14:02:15 EDT 2009 | swag

As mentioned previous, check all fuses & breakers. In the AC chassis (should be under black cover beind front, right door), remove cover and check main circuit breaker. Also should be two fuse housings next to breaker - if they are lit up amber, th

recently purchased MPM Ap Hie - startup trouble

Electronics Forum | Thu May 01 07:33:19 EDT 2008 | realchunks

Jim, You need to repair or by-pass the cover interlock. The machine thinks it's open and will not procede any further. They all do it, even the new models. Once you get past this warning - you will get the the RESET window - garanteed.

Skewed components

Electronics Forum | Thu Mar 08 14:30:45 EST 2007 | ratsalad

If you are in the middle of a run and can't get a replacement stencil there immediately, you can always put a little kapton tape on the bottom of the stencil to mask off a portion of the DPAK pad and reduce the paste deposit. We have had to do this

Business/Manufacturing Operational Changes to Comply with Local/National COVID-19 Regulations

Electronics Forum | Thu Apr 09 11:37:49 EDT 2020 | stephendo

You can tell that Ontario's list of essential services was written by a business man that understands the supply chain. The first list was something like 74 paragraphs. The second edition was something like 40 some paragraphs. One paragraph covers p

Re: Siemens Reliability

Electronics Forum | Tue Mar 09 13:53:21 EST 1999 | Tom B.

We use Siemens equipment at our plant. I agree with what everyone said in the forum. These machines are primarily made for fixed or specfic PCB runs. The feeders are very well built as others have metioned. If you plan on excessive change over's,

External Factors to be controlled during assembly

Electronics Forum | Thu Sep 27 19:52:28 EDT 2001 | davef

All of the discussion of "environmental controls" are a matter of degree, dependent on the requirements of the product that you manufacture. For example: shops assembling under-the-hood products have different requirements than shops making garage d

  1 2 Next

mpm cover door open searches for Companies, Equipment, Machines, Suppliers & Information

fluid dispenser

Stencil Printing 101 Training Course
Win Source Online Electronic parts

Software programs for SMT placement and AOI Inspection machines from CAD or Gerber.
Circuit Board, PCB Assembly & electronics manufacturing service provider

Best Reflow Oven