Electronics Forum | Wed Aug 30 13:26:29 EDT 2017 | fuji_user_2014
Hello Gurus, I'm looking for information on FOD generated by routers, more specifically a vacuum equipped Cencorp 1000BR. I want to ensure that this machine can route a populated panel without needing a wash afterwards in order to meet IPC CL3 sta
Electronics Forum | Fri May 22 22:18:18 EDT 1998 | David Newman
Hello, I am looking for suggestions for cleaning pcb's after the routing (fabrication) process. Keep in mind that these pcb do not have components intalled on them yet. We have considered pre-drilling the routing plunge points, but cost and capacity
Electronics Forum | Tue Oct 29 08:07:53 EDT 2013 | cyber_wolf
Are there a set of guidelines for optimizing panel design for tabs that will be removed with a board router ? In other words we need to know how to layout the tabs. Thanks
Electronics Forum | Tue Nov 26 15:32:41 EST 2013 | boriskilk
As with most questions the answer is; it depends. Provided not too many boards are set onto a panel we use a .10" router gap around the PCB and .10" wide perforated tabs. We do request customers specify where they do not want tabs to ensure no breako
Electronics Forum | Thu Jun 04 22:18:40 EDT 1998 | David Newman
1/8" cutters, although they can only be used with our newer height-controlled machines. 3. Reduction of operating parameters. Reduced Z-axis plunge rates for the larger cutter sizes. 4. Addition of a 1/2 sec. dwell at the plunges. The small pause he
Electronics Forum | Sun May 24 06:02:33 EDT 1998 | Earl Moon
| Hello, | I am looking for suggestions for cleaning pcb's after the routing (fabrication) process. Keep in mind that these pcb do not have components intalled on them yet. | We have considered pre-drilling the routing plunge points, but cost and ca
Electronics Forum | Tue Jun 09 17:01:02 EDT 1998 | Earl Moon
1/8" cutters, although they can only be used | with our newer height-controlled machines. | 3. Reduction of operating parameters. Reduced Z-axis plunge rates for the | larger cutter sizes. | 4. Addition of a 1/2 sec. dwell at the plunges. The small
Electronics Forum | Wed Jan 13 04:27:00 EST 2016 | crystalpcb
Hi Here is our factory production capability: Shenze Electronic PCB Specification Layer Count 1 to 35 Layers Material Brand Shengyi,KB,GRACE,ISOLA,Rogers,Taconic,ARLLON,Bergquist Base Material FR-4（TG135,TG150,TG170,TG180），Halogen Free FR-4，Ceramic
Electronics Forum | Thu Aug 22 22:10:26 EDT 2002 | davef
Ooooow! �Can it be fixed?� Good question. How BAD did you damage it? * Since you are asking this question, I am NOT inspired by the potential that you have the skills to fix the board. Go Jeff Ferry�s site at Circuit Repair Center [If you can�t f
Electronics Forum | Thu Jul 27 10:57:35 EDT 2017 | fkn
We make pcb depaneling equipment and many of our customers do a combination of tab routed panels with pre-score in order to speed up the singulation process. If you like, I can send you a picture of an example. Regards Klaus Heimann FKN Systek Tel.
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
1750 Mitchell Ave.
Oroville, CA USA
Phone: (888) 406-2830
winsouce.jpg)