Electronics Forum | Thu Oct 02 10:43:37 EDT 2008 | msangabriel
I am looking for companies that fabricates special or custom SMT feeders for an Fuji IP3 machine. It is to feed a SMT terminal. Do you know of any company that you can recommend?
Electronics Forum | Mon Sep 17 15:27:51 EDT 2001 | jschake
Challenges: The basic defects that impact assembly yield are bridging, satellite solder balls, and opens (i.e. tombstones / draw bridges). There are many variables with the stencil printing process that can impact these; several of them are listed
Electronics Forum | Fri Jul 16 14:34:18 EDT 1999 | Glenn Robertson
| We are converting from COB to SMT on a product line and want to optomize the PCB as far as Laminate, plating, passivation etc. This is a high temp application 150C. We are presently using BT Laminate but would like to get away from this. We are
Electronics Forum | Mon May 11 17:35:01 EDT 1998 | Steve Gregory
On 11 May, 1998 Todd wrote: | We are having continuous bridging problems with the trailing | leads on a 26-pin D-sub through-hole connector. The pitch is | 0.100". The connector is going through the wave at approximately | a 20 Degree angle. Does
Electronics Forum | Mon Apr 26 11:04:53 EDT 1999 | Dave F
| | Earl said, in essence: | | | | | Justin is absolutely right ... | | | | | | Again, Entek is not much more than a flux coating ... | | | | | | Metallic coatings protect best, as we all know - especially those electroplated. Those coatings chemi
Electronics Forum | Mon Apr 26 17:45:26 EDT 1999 | Earl Moon
| | | Earl said, in essence: | | | | | | | Justin is absolutely right ... | | | | | | | | Again, Entek is not much more than a flux coating ... | | | | | | | | Metallic coatings protect best, as we all know - especially those electroplated. Those
Electronics Forum | Fri Jan 16 10:08:28 EST 1998 | Dave A.
| We are looking for a good solder/desolder machine for state-of-the-art pcb rework. | A step up from the Pace/OK Industries is the level I am researching. | The application is a nice R&D Lab on state-of-the art PCBs. | Anybody who has suggestions or
Electronics Forum | Tue Sep 07 09:11:33 EDT 1999 | Dave F
| We've noticed that there are many different recommendations for pad sizes for various SMT parts. This seems to vary wildly from manufacturer to manufacturer for the same case sizes. Is there any standards that can used used to specify these sizes
Electronics Forum | Tue Sep 16 17:03:34 EDT 2014 | rangarajd
We have an issue with solder wicking up the leads/ inside terminations on an SMT connector. The solder coverage is sometimes over 50% of the connectors inside pin length. The terminations are gold plated. Is there an IPC spec for acceptability? Plea
Electronics Forum | Thu Oct 26 18:43:09 EDT 2000 | Christopher Noonan
I am looking for tooling plate manufactures. I am kind of new to the SMT process, well as far as tooling goes, and I am trying to find a machinist to make tooling plates for Fuji and Siemens placement machines. Does anyone have any recommendation f
Main Products: 1. Original new and Original Used SMT/AI Spare Parts. 2. SMT Equipments And Related Machine( SMT Calibration, SMT Feeder Carts,Conveyer etc.) 3. Maintenace and Repair Service Pre-Sales Service Provide details ab
Manufacturer's Representative / Manufacturer / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
Building A, Jiepeng Square, Fuyong
Shenzhen, 30 China
Phone: 0755-33578694
winsouce.jpg)
.gif)
