ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/products/efd-products/400-series-autovalve
Valve, Single Air Cylinder, TPV Seals Two-Component (2K) Products View All 2K Products Accurately Mix and Dispense Nordson EFD leads the way with industrial mixing systems that are uniquely designed to accurately mix and dispense two-part adhesives and
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/products/efd-products/450-series-autovalve
, Extended Air Cylinder w/Snuff Back, GT Seals Two-Component (2K) Products View All 2K Products Accurately Mix and Dispense Nordson EFD leads the way with industrial mixing systems that are uniquely designed to accurately mix and dispense two-part adhesives and
| https://www.eptac.com/faqs/ask-helena-leo/ask/bridging-two-adjacent-pins-on-an-ic
. Verify the wire solders properly to the leads, i.e., good wetting to both wire and component leads. If the wire is a small enough gauge, then it can be wrapped around the component lead and that would also be acceptable. See section
| https://www.eptac.com/faqs/ask-helena-leo/ask/gullwing-lead-deformation
% of the diameter, width, or thickness of the lead, they cannot be used. The 001 Handbook states on page 58, section 7.1.1 Lead Deformation: “After forming, component leads may be deformed up to 10
| https://www.eptac.com/faqs/ask-helena-leo/ask/75-barrel-fill-requirement-for-class-2-change-in-j-std-001-revision-f
? Revision E allowed 50% when there was a thermal plane. Now, Rev. F states 75% regardless of thermal plane. It all depends on how many leads the component has, with 14 being the magic number
| https://www.eptac.com/faqs/ask-helena-leo/ask/shelf-life-of-soldered-components
component storage, environment used to store component until soldered, and handling methods used on the component until soldered. Solderability of component leads is included in EIA/IPC/JEDEC J-STD-002D Solderability Tests for Component Leads, Terminations, Lugs, Terminals and Wires
| https://www.eptac.com/faqs/ask-helena-leo/ask/ipc-a-610-revision-f-paragraph-7-3-5-1-supported-holes-solder-vertical-fill-a
: Minimum vertical fill of 50% or 1.2 mm for components with 14 or more leads. What is the importance of 14 or more leads? Does the vertical fill depend more on the thermal layers and not the number of leads? 2. Defect – Class 2: Revision ‘E
| https://www.eptac.com/faqs/ask-helena-leo/ask/smt-components-during-reflow-float-off-pads
mass of solder and pulls the leads off the pads, resulting in no heel fillets. The component lead land areas need to be longer to accept this movement of the component on the large thermal pad
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/industrial-coating-systems/additional-product-sub-type/continuous-coater?con=t&page=5
instant color selector is designed for precision dispensing and ultra-fast contamination-free color change. Finishing Finesse – A quest for the ultimate in quality and collaboration leads this cutting-edge job shop to the latest in powder color-change technology
| https://www.eptac.com/faqs/ask-helena-leo/ask/post-lead-trimming-reflow-requirements
“leads must be covered by solder”. Can you elaborate on where I may find more conclusive... Question: I’m having trouble discerning the requirements for post lead trimming reflow in the new version of IPC-A-610
COT specializes in high quality SMT nozzles and consumables for pick and place machines. We provide special engineering design service of custom nozzles for those unique and odd components.
2481 Hilton Drive
Gainesville, GA USA
Phone: (770) 538-0411
winsouce.jpg)
.gif)
