Technical Library | 2023-01-17 18:04:51.0
As a manufacturing technology, SMT has acquired a "heritage" of widely accepted assumptions about its processes. However, yesterday'spractices are continually confronted by the shifting paradigms of today's production line.
Technical Library | 2023-08-16 18:25:16.0
In one of our Consumer Electronics projects, a leader of networking technologies requested to test dispensing performance of a thermally conductive material, Fujipoly Sarcon SPG-50A. This material improves heat dissipation for higher frequency applications and reduces the negative effects of thermal resistance under heat, cold, humid, and thermal shock conditions. The customer's goal was to dispense a 1mm diameter dot with acceptable speed and consistency.
Technical Library | 1999-05-06 11:52:21.0
The market's demand for increasingly powerful products, in smaller and smaller packaging, creates a cooling problem. Integrated circuit (IC) lifetime is dependent upon its operating temperature, creating a trade-off situation: either you enlarge the package to accept additional cooling, or you sacrifice IC lifetime.
Technical Library | 2010-04-22 14:55:51.0
It is now widely accepted that using designed experiments is the most effective way to optimize surface mount technology (SMT) processes. This situation begs the question "what is an effective strategy in implementing this powerful tool?" This paper will present such a strategy that incorporates Taguchi's approach for screening, full factorial analysis for optimization and central composite design for precise modeling. We will present these techniques using MINITABTM Release 13 statistical software and printed circuit board industry applications.
Technical Library | 2023-01-10 20:03:37.0
Since the IPC-4552 rev A for ENIG was introduced there have been many requests for clarification of acceptable and unacceptable levels of nickel corrosion. This paper attempts to further clarify the effects of nickel corrosion on solder wetting balance test results and the resultant intermetallic formed. The study will attempt to produce level 1, level 2, and level 3 corrosion as denoted by IPC-4552 rev A and tabulate wetting balance results and congruity of intermetallic formed.
Technical Library | 2023-06-12 19:07:04.0
In this article we will examine if there is a measurable difference in the printing performance when using stencils which have a higher tension than is commonly accepted in the industry. Alpha's new tensoRED™ High Tension Frame System will be introduced during this wider examination. We will examine their effect in terms of controlling variation in critical deposit volumes and what, if any effect on positional accuracy can be seen.
Technical Library | 2008-04-15 14:43:08.0
The increasing demands for miniaturization and better functionality of electronic components and devices have a significant effect on the requirements facing the printed circuit board (PCB) industry. PCB manufactures are driving for producing high density interconnect (HDI) boards at significantly reduced cost and reduced implementation time. The interconnection complexity of the PCB is still growing and today calls for 50/50 μm or 25/25 μm technology are real. Existing technologies are unable to offer acceptable solution. Recently the Laser Direct Imaging (LDI) technology is considered as an answer for these challenges.
Unipress - Institute of High Pressure Physics of the Polish Academy of Sciences
Technical Library | 2007-11-29 17:20:31.0
Programs have been developed to predict the expected yield of flip chip assemblies, based on substrate design and the statistics of actual manufactured boards, as well as placement machine accuracy, variations in bump sizes, and possible substrate warpage. These predictions and the trends they reveal can be used to direct changes in design so that defect levels will fall below the acceptable limits. Shapes of joints are calculated analytically, or when this is not possible, numerically by means of a public domain program called Surface Evolver. The method is illustrated with an example involving the substrate for a flip chip BGA.
Technical Library | 2008-12-18 01:34:49.0
Unless you've been living under a rock the past several years, you are no doubt keenly aware of the global drive toward alternative energy sources. Certainly this initiative is attractive because of the clear environmental benefits of developing fossil fuel substitutes, but also because of potential economic benefit. Although fuel cell technology has been proven viable for various applications, the production costs still remain relatively high, and further process development to promote low-cost, high-volume manufacturing is required to reach a price point that encourages widespread consumer acceptance.
Technical Library | 2010-03-18 14:02:03.0
Selecting products that have been qualified by industry standards for use in printed circuit board assembly processes is an accepted best practice. That products which have been qualified, when used in combinations not specifically qualified, may have resultant properties detrimental to assembly function though, is often not adequately understood. Printed circuit boards, solder masks, soldering materials (flux, paste, cored wire, rework flux, paste flux, etc.), adhesives, and inks, when qualified per industry standards, are qualified using very specific test methods which may not adequately mimic the assembly process ultimately used.
.gif)
winsouce.jpg)