New Equipment | Solder Paste Stencils
Simplify and Speed Up QFN and LGA device rework. StencilMate™ leadless device rework stencils make the process of reworking leadless devices such as QFNs and LGAs simple and fast. These adhesive-backed poyimide stencils are placed on to the bottom o
New Equipment | Solder Paste Stencils
Step-up / Step-down Stencil. The patented step stencil from LaserJob, called PatchWork® - stencil, was developed to print in one printing step different paste deposit heights. Due to the multiplicity of different component leads on one printed circu
Electronics Forum | Fri Jul 13 19:08:55 EDT 2001 | mparker
Home plate apertures are designed to reduce or eliminate solder balls that occur when placing a chip and reflow of the solder. This aperture type is usually desired when processing with a "no-clean" solder paste. The design of the aperture is usually
Electronics Forum | Wed Jan 08 08:20:52 EST 2014 | emeto
To most of our boards I give 20-30% tolerance in both directions. From experience if you have big aperture on your stencil, the squeegee will scoop certain amount of paste from this aperture and you will see lower height. Depending on your board supp
.JPG)
Used SMT Equipment | SPI / Solder Paste Inspection
The LSM300 follows the successful Laser section Microscopes LSM and LSM2. This new non-contact laser based system is an off-Line solder paste inspection system.LSM300 provides automatic height measurements, eliminating the inconsistencies of manual m
Used SMT Equipment | AOI / Automated Optical Inspection
This AOI was purchased for $49,995 from Manncorp. The Sherlock AOI is in excellent condition and has under 200 hours of usage. The Sherlock AOI Systems detect a comprehensive range of defects and errors in PCB assembly using the Sherlock PCB ins
Industry News | 2003-03-26 08:25:40.0
The QVE00033 transmissive switch's small size, surface mount package and performance make it ideal for noncontact switching applications in disk drives, card detectors, mise and trackballs.
Industry News | 2002-02-04 18:10:34.0
Clean stencils used for backplane, motherboard and other large stencil printing applications
Technical Library | 2023-08-04 15:27:30.0
A designed experiment evaluated the influence of several variables on appearance and strength of Pb-free solder joints. Components, with leads finished with nickel-palladium-gold (NiPdAu), were used from Texas Instruments (TI) and two other integrated circuit suppliers. Pb-free solder paste used was tin-silver-copper (SnAgCu) alloy. Variables were printed wiring board (PWB) pad size/stencil aperture (the pad finish was consistent; electrolysis Ni/immersion Au), reflow atmosphere, reflow temperature, Pd thickness in the NiPdAu finish, and thermal aging. Height of solder wetting to component lead sides was measured for both ceramic plate and PWB soldering. A third response was solder joint strength; a "lead pull" test determined the maximum force needed to pull the component lead from the PWB. This paper presents a statistical analysis of the designed experiment. Reflow atmosphere and pad size/stencil aperture have the greatest contribution to the height of lead side wetting. Reflow temperature, palladium thickness, and preconditioning had very little impact on side-wetting height. For lead pull, variance in the data was relatively small and the factors tested had little impact.
Technical Library | 2023-07-25 16:50:02.0
Some of the new handheld communication devices offer real challenges to the paste printing process. Normally, there are very small devices like 01005 chip components as well as 0.3 mm pitch uBGA along with other devices that require higher deposits of solder paste. Surface mount connectors or RF shields with coplanarity issues fall into this category. Aperture sizes for the small devices require a stencil thickness in the 50 to 75 um (2-3 mils) range for effective paste transfer whereas the RF shield and SMT connector would like at least 150 um (6 mils) paste height. Spacing is too small to use normal step stencils. This paper will explore a different type of step stencil for this application; a "Two-Print Stencil Process" step stencil. Here is a brief description of a "Two-Print Stencil Process". A 50 to 75 um (2-3 mils) stencil is used to print solder paste for the 01005, 0.3 mm pitch uBGA and other fine pitch components. While this paste is still wet a second in-line stencil printer is used to print all other components using a second thicker stencil. This second stencil has relief pockets on the contact side of the stencil any paste was printed with the first stencil. Design guidelines for minimum keep-out distances between the relief step, the fine pitch apertures, and the RF Shields apertures as well relief pocket height clearance of the paste printed by the first print stencil will be provided.
ALPHA® TETRABOND™ is the culmination of "frameless" stencil development; an elegantly simple system designed to enhance the rigidity of the foil, making safe mounting and demounting an easier proposition. Innovatively encompassed in a thin, one piece
Career Center | , | Engineering,Production
Project Management, SMT Process Engineering
Career Center | Theni, Tamilnadu India | Engineering
NPI Engineer: • Playing a role as NPI leader of the Telecom, Aerospace & Server Products to introduce and run to qualify the engineering build from customer. • Conducting Weekly NPI meeting with the CFT team to review the progress of the NPI schedu
Process Development And Characterization Of The Stencil Printing Process For Small Apertures Process Development And Characterization Of The Stencil Printing Process For Small Apertures. The consumers interest for smaller, lighter and higher
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/it-IT/divisions/efd/products/solder-paste/printplus-printing-paste
? Richiedi un preventivo
| http://www.thebranfordgroup.com/dnn3/Auctions/RecentAuctions.aspx
] SOLD - Auction Closed on 8/31/2022 Branson & Dukane Ultrasonic Welders! 2nd in a Series – Incredible Opportunity 2,500-Watt to 4,000-Watt Welders Available New in 2020 and Prepped for Shipping Tempe, AZ Aperture Solutions & Pues LLC [Online] SOLD
winsouce.jpg)
