Industry Directory | Consultant / Service Provider / Distributor / Equipment Dealer / Broker / Auctions / Manufacturer / Manufacturer's Representative
DONGGUAN KINGSUN AUTOMATION TECHNOLOGY CO.,LTD is a company which mainly provide used and new SMT parts, provide repair SMT key parts service,new/used SMT machine trading,SMT consumables and Peripherals equipment,Clean room, ESD..
Industry Directory | Manufacturer
DONGGUAN KINGSUN AUTOMATION TECHNOLOGY CO.,LTD is a company which mainly provide used and new SMT parts, provide repair SMT key parts service,new/used SMT machine trading,SMT consumables and Peripherals equipment,Clean room, ESD..
High Precision Dispensers - MAX Series (Non-Heated) Max Series is capable of a wide variety of dispense applications including MicroVolume, Solder Paste and Conductive Adhesive, Underfill, Surface Mount Adhesive, Dam and Fill, Encapsulations, LED En
The device eliminates the conventional vacuum chamber board fixture that is common on most MPM printers and is retrofitted in approximately one hour. Q-Lok provides secure, "over the top" type PCB clamping as well as a tool-less, hands-off product
Electronics Forum | Wed Mar 13 14:17:03 EST 2002 | dougt
Are these sensors the reflective type? Maybe when the board is unclamped and it goes over the sensor it is seen, and then when it is clamped (raised) it is now out of the range the sensor was set for. That should be easy to adjust. A problem I've
Electronics Forum | Fri Mar 08 12:22:18 EST 2002 | pr
Have you contacted Fuji? I believe we had the same situation a while back and (I think) it was a proper setting and not a sensor problem. A tech. can probably walk you through it over the phone. good luck, pr
Used SMT Equipment | SMD Placement Machines
* DOS * Flying Nozzle change * Fiducial camera * Pneumatic tape feeder * Locate Pin * Edge clamp * Z servo push plate * Entrance sub stop * Exit sub stop * Auto width adjust * Feeder float detection
Used SMT Equipment | Screen Printers
2003 DEK Horizon 01 Screen Printer *** Note: This lot contains two items. (1) DEK Horizon 01 Screen Printer (1) DEK VF35 Vacuum System Approx Dimensions: 70" x 70" x 68" Location: Jasper, IN USA Serial: 281505 Features: o Advantec 2.05 Computer syste
Industry News | 2003-03-17 09:40:03.0
Omnimate BLZ/BLZF 5.08F PCB connectors have integral screwed flanges to ensure safe and secure connection under the most severe vibration conditions.
Industry News | 2003-05-19 08:44:19.0
Two new PCB power connectors offer easy high power wiring (up to 54A) with built-in safety features to prevent incorrect connections and resist strong vibration.
Parts & Supplies | SMT Equipment
Rail clamping shaft(107424) GUIDE BAR, 7.999mm DIA, 25mmLG-DEK pin Kindly contact me if you are interested. Email: alice@ksunsmt.com Skype: alice@ksunsmt.com Whats app: +86 13170471806 Face book: alice@ksunsmt.com
Parts & Supplies | SMT Equipment
Rail clamping shaft(107424) GUIDE BAR, 7.999mm DIA, 25mmLG-DEK pin Kindly contact me if you are interested. Email: alice@ksunsmt.com Skype: alice@ksunsmt.com Whats app: +86 13170471806 MP: 0086-13170471806
Technical Library | 2010-05-06 18:46:29.0
Stencil printing technology has come a long way since the early 80’s when SMT process gained importance in the electronics packaging industry. In those early days, components were fairly large, making the board design and printing process relatively simple. The current trend in product miniaturization has led to smaller and more complex board designs. This has resulted into designs with maximum area utilization of the board space. It is not uncommon, especially for hand held devices, to find components only a few millimeters from the edge of the board. The board clamping systems used in the printing process have become a significant area of concern based on the current board design trend.
Technical Library | 2016-08-24 06:15:35.0
From consumer electronics to systems control, automotive technology to aviation and aerospace – today, electronics are absolutely essential in many sectors. They increasingly replace mechanical components, eliminating wear and tear and thereby extending the service life. What is easily forgotten in this regard is that electronics are also subject to the laws of mechanics. Mechanical test equipment is crucial to test components for the secure hold of welded, soldered or adhesive bonds. A new, mechanically intricate test probe with universal clamping jaws, that can even grasp the individual bonding wires, is in line with the trend toward ever smaller components. Serving as an actuator for these is a micro drive that can be precisely controlled using a miniaturised motion controller to relieve the control unit in the test device.
High Precision Dispensers - MAX Series (Non-Heated) Max Series is capable of a wide variety of dispense applications including MicroVolume, Solder Paste and Conductive Adhesive, Underfill, Surface Mount Adhesive, Dam and Fill, Encapsulations, LED En
J7065407B CLAMP LEVER 1 J2500273 CLAMP SPRING PIN 1 J2500231 PIN 7 J2500315 CLAMP LEVER 2 J2500231 PIN 7
Career Center | Torrington, Connecticut | Engineering,Management,Production,Quality Control,Sales/Marketing,Technical Support
MECHANICAL AND ELECTRONIC CAD TECHNOLOGY-CERTIFICATION • TECHNICAL DRAFTING: Equipment Use, Orthographic Projection, Dimensioning, Auxiliary Views, Fasteners, Manufacturing Processes and Fits and Tolerances • POWER TRANSMISSION/ANSI 14.5 1994: Bearin
Career Center | , District of Columbia | Engineering,Management,Production,Sales/Marketing
• Strong technical leadership and decision-making skills; strong verbal and written communication skills to provide clear, crisp direction for key issue resolution; and good team skills to facilitate cross-functional cross -site team effectiveness.
Effect Of Board Clamping System On Solder Paste Print Quality Effect Of Board Clamping System On Solder Paste Print Quality Stencil printing technology has come a long way since the early 80s when SMT process gained importance in the electronics
| http://www.szhonreal.com/productview.asp?id=100
Board size minimum 50×50mm maximum 1 buffer 650×370 mm （ Single clamping ） 950×370 mm （ double clamping ） 1,100×370 mm （ double clamping ） 1,200×370 mm （ double clamping ） 3 buffers 360×370 mm 500×370 mm 600×370 mm Component height 25 mm Component size 0201
KD Electronics Ltd. | http://www.kundasmt.com/a/PRODUCTS/2970.html
EQUIPMENT Equipment Accessories REFLOW FURNACE MPM DEK Rehm HELLER OTHER PARTS CONTACT US SURFACE MOUNT SYSTEM Product number:03020530-01 Description: Clamping plate
