Software solution to the electronics industry - control & diagnostics systems
The Static Problem Electrostatic charging generates a significant amount of unwanted and potentially damaging electromagnetic interference (EMI) through both triboelectric and inductive charging. The charging occurs primarily in and around electron
Electronics Forum | Fri Sep 13 10:56:05 EDT 2002 | slthomas
For starters, can you verify that the seal integrity is still intact?
Electronics Forum | Fri Nov 07 16:00:45 EST 2003 | Don A
It would depend on how many boards and parts you need to build. I would prefer an etch cut as it leaves the the part intact and you get the strength of the solder joint. It also reduces the handling of the BGA and associated damage from that
Used SMT Equipment | Pick and Place/Feeders
1998 Philips Topaz Pick & Place 2 Machines! Machine1: working Model: Topaz Vintage: 1998 Hours: 16,315 Condition: Fully Operational, except two of the eight heads are not in use, and condition unknown. Machine 2: spares machine, all h
Used SMT Equipment | Soldering - Reflow
Reflow welding machine is a very important equipment in SMT production process. Reflow welding process directly affects the quality of SMT process. It is difficult to achieve good reflow welding quality without a good reflow A welding machine. [1]
Industry News | 2003-03-28 09:11:29.0
Announced that plans for its two upcoming exhibitions and conferences, IPC Printed Circuits Expo� 2003 and IPC SMEMA Council�s APEX� 2003, remain intact, despite the latest developments in the Middle East and around the world.
Industry News | 2020-07-01 12:08:16.0
For high precision low stress PCB singulation of panels with sensitive components near the parting edge, and with the smooth edge finish required by military specifications or by packaging considerations, using a Diamond Blade Saw beats routing for speed and for blade life. The saw blade, a 2.95" (75mm) diameter .021" thick diamond coated cutting disk, provides a low-stress, ultra smooth edge finish for separting panelized Printed Circuit Cards. ts which overhang the parting line will remain intact.
Parts & Supplies | SMT Equipment
ONE AVAILABELE, REMOVED FROM A GOOD WORKING MV2 SERIES MACHINE, USED UNIT BUT INTACT AND VERY CLEAN, MODEL 932-11-1, SERIAL 181217
Technical Library | 2023-08-14 09:06:53.0
In the operation of SMT mounter, the process and integrity of the nozzle of the mounter will have a significant impact on the performance of the machine. As one of the important components of the SMT machine, it is necessary for us to carry out daily maintenance and upkeep of the SMT nozzle. To ensure that the suction nozzle of the SMT machine is intact before operation, how should we do a good job of maintaining the suction nozzle of the SMT machine during normal use? KINGSUN technical team analysis operation has the following main points: 1.Wipe the surface of the SMT nozzle with a dust-free cloth. 2.The small aperture nozzle can be passed through with a thin steel wire and then blown with an air gun. 3.The surface of the nozzle should not be soaked with corrosive solution such as alcohol, as this may cause the surface to fall off. 4.HOLDER should use a cotton swab to wipe the cavity and not damage the filter screen. 5.Regular addition of special grease to HOLDER claws. 6.According to production, it is best to regularly maintain and do other maintenance regularly. (* Suitable for Yamaha SMT machine nozzles , JUKI SMT machine nozzles, Samsung SMT machine nozzles, Panasonic SMT machine nozzles, Fuji SMT machine nozzles, Siemens SMT machine nozzles etc.) Regarding the SMT machine nozzle daily maintenance operation instructions, KINGSUN share with you here , hoping to be helpful to you. More information about Products please Contact US at jenny@ksunsmt.com or visit www.ksunsmt.com , thanks.
Technical Library | 2008-11-13 00:06:32.0
The electronics industry is facing issues with hot spots, solder joint stresses and Coefficient of Thermal Expansion (CTE) mismatch between PCB and IC substrate. Flip chip type packages for example have very low CTE compared to traditional PCB material. Thus it is necessary to have low CTE printed circuit boards in order to keep solder joint intact with such low CTE packages. There are currently several materials available in the market to address thermal and CTE challenges but each material has its own advantages and limitations...
ACI Technologies Inc. (ACI) is a scientific research corporation dedicated to the advancement of electronics manufacturing processes and materials for The Department of Defense and industry. This video provides an overview of our commercial service
Product introduction: 1.Steel frame, static painted surface; 2.Balance weight design improve the stability; 3.Reject,inspection,pass,three mode optional; 4.Smooth and parallel width adjustment(leadscrew); 5.According the customer’s damand to c
PCB Libraries, Inc. | https://www.pcblibraries.com/forum/RSS_pad-stack-manager_topic1992.xml
(SIP), where I have entered all my data.It's from here it would be useful to enter the FP Designer. (with data intact) Pad Stack Manager : Did you select the
