Failure analysis - Components as well as PC boards, Discretes, Passives ICs - offering X-ray. SEM/EDX -XRF - Cross sectioning complete root cause F/A
Industry Directory | Distributor / Equipment Dealer / Broker / Auctions / Manufacturer / Media / Publisher / Online Resource
All Through-hole & SMT PC Board Assembly equipments,Reflow and wavesoldering equipments,Humiseal conformal coating,SCH Technologies conformal coating equipments,Kyzen Cleaning solutions,Metronelec Solderability tester,Curing oven
ProntoTEST-FIXTURE used by electronics manufacturers will accurately setup your Automatic Test Equipment (ATE), Flying Probe and design your "bed of nails" test fixturing. In minutes Unisoft ProntoTEST-FIXTURE software translates CAD and Bill of Ma
40 and 64 position stacking connectors in short and long tail version offered in pressfit. Eliminates secondary soldering opertations and improves product quality.
Electronics Forum | Sun Sep 15 15:08:00 EDT 2002 | jersbo
My 2 cents... Screen printing may very well have a leg up on deciding SMT defects... however if you pay attention to your stencil (aperture size ratio etc..) and inspect your prints... I believe its a much lesser number... (paste MFG also plays a ro
Electronics Forum | Mon Nov 11 08:47:00 EST 2013 | mleber
Thanks guys. Here are more details. The cards are essentially the same. They use the same connectors, same footprint, the traces / layers would be comparable etc. The difference between the 2 we see is that one is laminate - Rigid Metal Clad Base, Ty
Used SMT Equipment | Cleanliness Testers
Cookson Electronics SCS - Specialty Coating Systems Ionograph 500M Model Number: SMD II Serial Number: 136848 Ionic Contamination Tester Voltage: 115V - 60HZ - 1 Phase Comes with PC and Accessories Includes Manual Good Condition Location: Bo
Used SMT Equipment | Assembly Accessories
2016 Tyco Press Model Number: CMP-6T (MEP-6T) Serial Number: 1020651/251 Max PCB Size: 24" x 36" 6 Ton Capacity 3-5 sec/connector Air Table Tool presence sensor Light Curtain PC with touch screen Windows 7 208/220 Volt - 3 Phase
Industry News | 2003-04-08 10:28:06.0
A new range of high-performance press-fit D-subminiature terminations from GTK can be fitted easily to PCBs without the need for solder.
Industry News | 2003-03-27 08:15:33.0
Modular Embedded Circuit Board from parvus Enables Local Device Fingerprint Biometrics
Parts & Supplies | SMT Equipment
Old driver card connector( P3251/P4720) Product Name: P3251; P4720 old driver card connector Part Number: P3251; P4720 Description: P3251; P4720 old driver card connector, 5PIN, male and female mating connector Applicable models: AP UP Printing
Parts & Supplies | SMT Equipment
Old driver card connector( P3251/P4720) Product Name: P3251; P4720 old driver card connector Part Number: P3251; P4720 Description: P3251; P4720 old driver card connector, 5PIN, male and female mating connector Applicable models: AP UP Printing
Technical Library | 2016-05-19 16:03:37.0
As consumers become more reliant on their handheld electronic devices and take them into new environments, devices are increasingly exposed to situations that can cause failure. In response, the electronics industry is making these devices more resistant to environmental exposures. Printed circuit board assemblies, handheld devices and wearables can benefit from a protective conformal coating to minimize device failures by providing a barrier to environmental exposure and contamination. Traditional conformal coatings can be applied very thick and often require thermal or UV curing steps that add extra cost and processing time compared to alternative technologies. These coatings, due to their thickness, commonly require time and effort to mask connectors in order to permit electrical conductivity. Ultra-thin fluorochemical coatings, however, can provide excellent protection, are thin enough to not necessarily require component masking and do not necessarily require curing. In this work, ultra-thin fluoropolymer coatings were tested by internal and industry approved test methods, such as IEC (ingress protection), IPC (conformal coating qualification), and ASTM (flowers-of-sulfur exposure), to determine whether this level of protection and process ease was possible.
www.unisoft-cim.com/pcbtest.htm - In minutes the Unisoft ProntoTEST-FIXTURE software translates CAD & BOM files into real reference designators, netlists, X/Y component pin geometries, values, tolerances, part numbers, etc. This data is used by Test
https://www.ascen.ltd/Products/conformal_coating_equipment//580.html PCB Conformal coating machine is used to paint conformal coating onto full LED panel to avoid PCB moisture,sault and static.It can be full panel conformal coating or selective coati
Training Courses | | | Other Courses
Other courses related to electronics manufacturing and assembly
Events Calendar | Tue May 08 00:00:00 EDT 2018 - Tue May 08 00:00:00 EDT 2018 | Milwaukee, Wisconsin USA
Training Workshop – “Improving Reliability of Continuity & HiPot Tests”
Events Calendar | Wed May 17 00:00:00 EDT 2023 - Wed May 17 00:00:00 EDT 2023 | Milwaukee, Wisconsin USA
"Risks of Over-Specifying Test Requirements: Testing Shielded Cables at High Voltage" | Conference Seminar | A Professional Development Course by CAMI Research
KingFei SMT Tech | https://www.smtspare-parts.com/sale-40328589-n510026303aa-panasonic-mounter-cm402-cm602-npm-cable-w-connector.html
N510026303AA Panasonic Mounter CM402 CM602 NPM Cable W Connector Leave a Message We will call you back soon! Your message must be between 20-3,000 characters
| https://www.eptac.com/faqs/ask-helena-leo/ask/soldering-minimum-space-requirements
: For soldering a wire into a connector fillet, what is the minimum space/area between the wire and the connector walls? Is there a standard for this? Question