New Equipment | Education/Training
All Bob Willis training workshops are run on site at your manufacturing facility, conference or exhibition venues Worldwide. We offer the largest range of theory and hands on workshops in the industry. The content of any workshop may be modified to s
New Equipment | Rework & Repair Equipment
Product Details DH-A2 BGA Rework Station 1.Application Of DH-A2 BGA Rework Station Suitable for different PCB. The motherboard of a computer, smartphone, laptop, MacBook logic board, digital camera, air conditioner, TV and other electronic equi
Electronics Forum | Wed Jan 31 01:41:00 EST 2001 | pjc
Steve, I have no influence over conn design. We paste print-reflow solder two types of connectors. One is a 50 pin IDC w/ 0.5mm lead dia @ 2.54mm lead pitch and a chamfered pointed lead tip. The other is 32 pin DIP w/ 0.36mm lead dia @ 2.54mm pitch
Electronics Forum | Tue Aug 25 20:33:31 EDT 1998 | Karlin
| | | | Hi, | | | | Does anyone has experiences in reflowing Ceramic BGA and found solder wicking ? Solder wicking has the syndrome that solder being wick from the pad and ended up in the leads. | | | | We have rule out the possibility of not printin
Industry News | 2003-06-12 08:24:37.0
An adaptive tool prevents small and/or light components "lifting" or "floating" on printed circuit board assemblies during the wave solder process.
Industry News | 2023-11-27 12:45:07.0
The Surface Mount Technology Association (SMTA) announces the release of several more webinars, photo libraries, and poster sets as part of a generous donation from renowned industry expert, Bob Willis.
Technical Library | 2019-06-21 10:39:15.0
Recently, an ACI Technologies (ACI) customer called to discuss failures that they had observed with some through-hole capacitor parts. The components were experiencing failures following vibration and accelerated stress testing. Upon receipt of the samples, ACI performed three levels of inspection and Energy Dispersive Spectroscopy (EDS) testing to investigate the root cause of the failures. These analyses enabled ACI to verify the elements comprising the solder joints and make the following recommendations in order to prevent future occurrences. The first inspection was to investigate the capacitor leads using optical microscopy, and no anomalies were found that could indicate bad parts from the vendor or improper handling prior to assembly. However, vertical fill in the barrel of the plated through-holes was too close to the IPC-A-610 minimum specification of 75% to determine a pass/fail condition, and therefore required further investigation.
Welcome to this Defect of the Month video on via hole failures and how to see them, this series of videos were produced for and featured as part of the NPL/IPC video library and examples are taken from the NPL Defect Database. Over the last couple of
ALPHA® Telecore XL-825 lead-free cored solder wire minimizes spattering in hand soldering operations, thus reducing circuit board contamination and enhancing worker safety and comfort.
Events Calendar | Mon Apr 06 00:00:00 EDT 2020 - Mon Apr 06 00:00:00 EDT 2020 | ,
Reflow Simulation – X-ray & Optical Help Solves Design & Process
Events Calendar | Wed Dec 06 00:00:00 EST 2017 - Wed Dec 13 00:00:00 EST 2017 | Rolling Meadows, Illinois USA
X-Ray of PCBs Webtorial
Career Center | Melbourne, Florida USA | Production
The SMD Repair / Operator performs all hand loading/unloading/operation of SMD line, manual soldering of Through-hole parts, inspection of PCBA's, and rework as required to support SMD production. Responsibilities: - Assists with manually load
Career Center | Dallas, Texas USA | Management,Production
Supervises an assigned work shift of 20+ employees. Typically has department group leaders as reports. Responsible for quality, quantity of work output and continuous improvement of product and/or processes. Establish, define, document and moni
Career Center | Fredericksburg, Virginia USA | Engineering,Maintenance,Management,Production,Quality Control
• Certified CP643 Loader Calibration – FUJI American Chicago, IL 2001. • Certified - Cookson Performance Solutions BTU - PARAGON - P150 Oven – Maintenance & Electrical Troubleshooting Charlotte, NC 2001. • Certified UNIVERSAL (GSM) Platform: Operat
Career Center | King, North Carolina | Management,Production,Quality Control
Production Supervisor Responsible for all aspects of department operations Directly supervised up to 80 team members Kaizen team leader 5S, Lean Manufacturing, working with Six Sigma tools Built team that continually produced 98% yields and Won
SMT Express, Volume 2, Issue No. 3 - from SMTnet.com Volume 2, Issue No. 3 Thursday, March 16, 2000 Featured Article Return to Front Page Stencil Design for Mixed Technology Through-hole / SMT Placement and Reflow by William E. Coleman, Photo
SMT Express, Volume 2, Issue No. 3 - from SMTnet.com Volume 2, Issue No. 3 Thursday, March 16, 2000 Featured Article Return to Front Page Curtailing Voids in Fine Pitch Ball Grid Array Solder Joints by Gary Morrison and Kevin Lyne
Blackfox Training Institute, LLC | https://www.blackfox.com/beginners-guide-to-surface-mount-soldering/
. Instead of components with leads inserted into holes as with “Through Hole” soldering, in this technique, components are attached to the pads on the board surface
| https://unisoft-cim.com/soldering_download.htm
ProntoSELECTIVE-SOLDERING and therefore your only option is to import raw Gerber files. ProntoSELECTIVE-SOLDERING can import and turn these raw Gerber files into real reference designators, theta rotation, part numbers, X/Y component pin geometries, etc. This data
