Form & Cut 2-, 3-, 4-, 5-, and 7-leaded Radial Components Capable of forming loose radial components at rates up to 5,000 parts per hour with a variable speed motor. Feed components by hand or with tubes (TO-220s) Reduce setup time with quick ch
Electronics Forum | Thu May 31 21:45:48 EDT 2012 | davef
rsthompson ... if you're talking about bare boards IPC-5701, Users Guide for Cleanliness of Unpopulated PBC, Table 8 ||Bare board final surface finish Ions||Hot air solder level||OSP over copper||Gold over nickel Chloride||0.75 ug/cm^2||0.75 ug/cm^2
Industry News | 2016-05-10 14:16:16.0
GPD Global offers individual pumps for integration into your existing platform – the Jetting NCM5000 Pump is one of them. The Jetting NCM5000 Pump simplifies jetting to its basic elements: hammer, pin, and nozzle. Only the pin and nozzle are wetted parts. This means easy set-up, cleaning, and upkeep.
Industry News | 2017-01-26 19:53:00.0
GPD Global will exhibit in Booth 2933 at the upcoming IPC APEX EXPO 2017 scheduled to take place February14-16, San Diego Convention Center. GPD Global will officially launch its new, fully automated dispense platform, Hyperion, and a new, low cost conformal coating system.
Technical Library | 2017-07-13 16:16:27.0
Controlled humidity and temperature controlled surface insulation resistance (SIR) measurements of flux covered test vehicles, subject to a direct current (D.C.) bias voltage are recognized by a number of global standards organizations as the preferred method to determine if no clean solder paste and wave soldering flux residues are suitable for reliable electronic assemblies. The IPC, Japanese Industry Standard (JIS), Deutsches Institut fur Normung (DIN) and International Electrical Commission (IEC) all have industry reviewed standards using similar variations of this measurement. (...) This study will compare the results from testing two solder pastes using the IPC-J-STD-004B, IPC TM-650 18.104.22.168 surface insulation resistance test, and IPC TM-650 2.3.25 in an attempt to investigate the correlation of ROSE methods as predictors of electronic assembly electrical reliability.
Technical Library | 2010-06-10 21:01:48.0
This paper researches the effectiveness of the R.O.S.E. cleanliness testing process for dissolving and measuring ionic contaminants from boards soldered with no-clean and lead-free flux technologies.
This is a video of the Universal GX-11S (4992B) placing components (0402, 0603, 0805, SOIC24, and QFP80) onto a pcb. The machine runs twice, once with automatic z update (azu) and once in full speed. This machine is available from the Capital Equip
Career Center | Tirunelveli, Tamil nadu India | Engineering,Maintenance,Quality Control,Research and Development,Technical Support
I have no experience but i will do my best in this department.i am very interest to work in manufacturing department.my interesting subjects are VLSI,CAD for VLSI circuits and its related subjects. VLSI languages,Ns2,c,c++,Ms office
Career Center | , California | Quality Control
Tammy T Vo P.O. Box 2213 (714) 254-5073 E-mail: email@example.com Position of Interest Senior Quality Inspector Aerospace Manufacturing. / Electronic PCBA/Advanced coating technologies Profile of Qualifications 12 years of experience wo
Validity of the IPC R.O.S.E. Method 2.3.25 Researched Validity of the IPC R.O.S.E. Method 2.3.25 Researched This paper researches the effectiveness of the R.O.S.E. cleanliness testing process for dissolving and measuring ionic contaminants from
!------------- REMOVE TEXT ABOVE THIS LINE ----------------- ! ! CONFIGURATION FOR TESTHEAD ! testhead name "testhead1" line frequency 60 relay 1 controls vacuum 2,3 relay 2 controls vacuum 0,1 !Bank 1 ! module 0
. Biocidal products regulation Active substances salicylic acid - 1.3 %Ingredient name Supplemental label elements : Contains 2,3-dibromo-2-butene-1,4-diol