Technical Library: 354 (Page 1 of 2)

Hand Printing using Nanocoated and other High End Stencil Materials

Technical Library | 2019-05-29 23:10:30.0

There are times when a PCB prototype needs to be built quickly to test out a design. In such cases where it is known early on that there will be multiple iterations or that a "one and done" assembly will be made that there will be some SMT assemblers who choose to hand print solder paste onto the board using a "frameless" stencil. In such cases where hand printing is used, the consistency of the printing technique has typically been in question. Furthermore, the effectiveness of both the nanocoatings as well as the higher end stainless steel materials, which have been heretofore studied in controlled printing environments, will be evaluated for their impact on the hand printing process.The purpose of the study was to determine the effectiveness of select nanocoating materials as well as certain high end stainless steel stencil materials as they relate to the manual SMT printing process. A variety of nanocoatings were applied to SMT metal stencils and solder paste volume measurements were taken to compare the effectiveness.

BEST Inc.

Round Robin of High Frequency Test Methods by IPC-D24C Task Group

Technical Library | 2017-06-29 16:39:30.0

Currently there is no industry standard test method for measuring dielectric properties of circuit board materials at frequencies greater than about 10 GHz. Various materials vendors and test labs take different approaches to determine these properties. It is common for these different approaches to yield varying values of key properties like permittivity and loss tangent. The D-24C Task Group of IPC has developed this round robin program to assess these various methods from the "bottom up" to determine if standardized methods can be agreed upon to provide the industry with more accurate and valid characteristics of dielectrics used in high-frequency and high-speed applications.

DuPont

Mixed Voltages And Aluminum Conductors: Assesing New Electrcal Technology

Technical Library | 2018-02-07 22:50:31.0

The architecture of vehicle electrical systems is changing rapidly. Electric and hybrid vehicles are driving mixed voltage systems, and cost pressures are making conductor materials like aluminum an increasingly viable competitor to copper. This paper presents tradeoff studies at the vehicle level, and how to automatically generate an electrical Failure Mode Effects and Analysis (FMEA) report, as well as how to optimize wire sizes for both copper and aluminum at the platform level.

Mentor Graphics

A New (Better) Approach to Tin Whisker Mitigation

Technical Library | 2011-03-03 16:54:47.0

Most of the electronics industry by now knows about tin whiskers. They know whiskers are slim metallic filaments that emanate from the surface of tin platings. They know these filaments are conductive and can cause shorts across adjacent conductors. And they know that these shorts can cause some really bad failures (see nepp.nasa.gov/whisker/ for a list longer than you need). But, with all of this knowledge, the industry is still struggling on how to predict and prevent these "Nefarious Needles of Pain".

DfR Solutions

Signal Transmission Loss due to Copper Surface Roughness in High-Frequency Region

Technical Library | 2015-04-30 20:17:03.0

Higher-speed signal transmission is increasingly required on a printed circuit board to handle massive data in electronic systems. So, signal transmission loss of copper wiring on a printed circuit board has been studied. First, total signal loss was divided into dielectric loss and conductor loss quantitatively based on electromagnetic theory. In particular, the scattering loss due to surface roughness of copper foil has been examined in detail. And the usefulness of the copper foil with low surface roughness has been demonstrated.

Mitsui Kinzoku Group

Challenges for Step Stencils with Design Guidelines for Solder Paste Printing

Technical Library | 2015-08-25 13:51:27.0

The stencil printing process is one of the most critical processes in the electronic production. Due to the requirement: "faster and smaller" it is necessary to place components with different paste volume close together without regard to solder paste printing. In our days it is no longer possible to control the solder paste volume only by adjustment of the aperture dimensions. The requirements of solder paste volumes for specific components are realized by different thicknesses of metal sheets in one stencil with so called step stencils. The step-down stencil is required when it is desirable to print fine-pitch devices using a thinner stencil foil, but print other devices using a thicker stencil foil. The paper presents the innovative technology of step-up and step-down stencils in a laser cutting and laser welding process. The step-up/step-down stencil is a special development for the adjustment of solder paste quantity, fulfilling the needs of placement and soldering. This includes the laser cutting and laser welding process as well as the resulting stencil characteristics and the potential of the printing process.

LaserJob

Printing of Solder Paste - A Quality Assurance Methodology

Technical Library | 2015-10-01 16:12:51.0

Solder paste printing is known to be one of the most difficult processes to quality assure in electronic manufacturing. The challenge increases as the technology development moves toward a mix between large modules and small chip components on large and densely populated printed circuit boards. Having a process for quality assurance of the solder paste print is fast becoming a necessity.This article describes a method to ensure quality secured data from both solder paste printers and inspection machines in electronic assembly manufacturing. This information should be used as feedback in order to improve the solder paste printing process.

Ericsson AB

Wave Solder Parameter Chart

Technical Library | 2006-05-13 13:07:53.0

This Excel Spreadsheet calculates the Wave Solder Contact Time automatically with given main Solder Wave width and Conveyor Speed. There is one chart where conveyor speed is expressed in meters/min and in another where it is expressed in feet/minute.

Jabil Circuit, Inc.

Case Study on the Validation of SAC305 and SnCu Based Solders in SMT, Wave and Hand-soldering at the Contract Assembler Level

Technical Library | 2007-11-15 15:54:44.0

At the contractor level once a product is required to be soldered with lead-free solders all the processes must be assessed as to insure the same quality a customer has been accustomed to with a Sn63Pb37 process is achieved. The reflow, wave soldering and hand assembly processes must all be optimized carefully to insure good joint formation as per the appropriate class of electronics with new solder alloys and often new fluxes.

Kester

A Study of PCB Insertion Loss Variation in Manufacturing Using a New Low Cost Metrology

Technical Library | 2012-06-27 18:26:34.0

First published in the 2012 IPC APEX EXPO technical conference proceedings. Signal integrity analysis has shown that printed circuit board (PCB) insertion loss is a key factor affecting high speed channel performance. Determining and controlling PCB inser

Intel Corporation

  1 2 Next

354 searches for Companies, Equipment, Machines, Suppliers & Information

Industry 4.0 Reflow Oven

Want to know where to find the best AOI system? - Read testimonials.
SMT spare parts - Qinyi Electronics

One-stop Platform For All Your Need For SMT - QYSMT
Best SMT Reflow Oven

High Resolution Fast Speed Industrial Cameras.
XTECH AUCTIONS

PCB Assembly Supplies - ONLINE STORE
one-stop for smt solution

SMT PARTS