Industry Directory | Consultant / Service Provider / Manufacturer
Cleanroom Equipments, validation using aerosol photometer ( DOP Test), Laser Particle Count Testing, Pressure Balancing, Air FLow Visualisation test and etc..
Industry Directory | Manufacturer
The international full service manufacturer of systems, detergents, equipment and process design for the cleaning in electronics production.
Precision Dispensing System for Heated Dispense Applications The GPD Global MAX II is a compact; high-accuracy system designed for today’s advanced heated dispensing applications. The frame is molded from “liquid rock” which gives the system a stabl
Time Pressure Liquid Dispensing Pump with Foot switch / Dry contact A great addition to Fully Automatic Dispensing System Time pressure is a versatile method of dispensing that functions across a wide range of viscosities. This dispensing method wo
Electronics Forum | Fri Feb 15 11:58:55 EST 2008 | rkeck
We are looking at an Omni Flow 5 Oven and do not have much information on it. We do know it has a 3" cabinet vent and a 6" vent near the center on the top. If anyone has knowledge of this oven, and has any suggestions or info, we would appreciate
Electronics Forum | Fri Feb 15 15:55:58 EST 2008 | pjc
This is from the OmniFlo 5 Engineering data sheet: EXHAUST SPECIFICATIONS: STANDARD AIR OPERATION: - Load-end: 150 cfm (255 m3/hr) at the 4� (102 mm) stack (minimum requirement) - Unload-end: 300 cfm (510 m3/hr) at the 4� (102 mm) stack (minimum req
Used SMT Equipment | Soldering - Wave
400V 50/60 HZ Version ERSAsoft for: 4.050.000.000 2. Operating System Dell / Windows 7 Processor: Pentium(R) Dual Core E5800 @ 3.20GHz 3.19GHz Memory RAM: 4.00 GB (3.46 GB usable) 320bit Operating System Touch Screen – No Pen Touch, input is availabl
Used SMT Equipment | SMT Equipment
Product Name: Panasoinc chip mounter CM88S-3 Product number: CM88S-3 Detailed product introduction High speed chip CM88C-M Panasonic Machine model: CM88C/S Machine year: 1999-2002 PCB size: Min:50*50 Max:330*250 Patch speed: 0.085 seconds /CH
Industry News | 2012-02-15 19:18:44.0
GPD Global announces that its PCD4H Dispense Pump yields excellent results with phosphor and non-phosphor-filled LED encapsulation as viewed on the color chart by tightly grouped results.
Industry News | 2003-04-28 08:12:02.0
The Micro-Meter 2 is an air-operated positive-displacement single-acting two-component system, designed to meter, mix and dispense small 'shots', or beads, of reactive materials.
Parts & Supplies | Pick and Place/Feeders
Device description: Machine Model: NXT-M3 Machine year: 2007 PCB Size: Minimum: 48mm X 48mm Max: 510mm X 534mm(dual track) Patch speed: H12HS: 22,500; H08:10,500; H04:6,500; H01:4,200 Paste accuracy: H12S/H08 / H04 :0.05 mm(3sigma) cpk ≥ 1.00 T
Parts & Supplies | Pick and Place/Feeders
FUJI(Japan) XPF-L Mater Device description: 1. Paste speed: rotation automatic replacement head: 0.144 SEC / 25,000 CPH Single suction mouth: 0.40 SEC / 9000 CPH Automatic change of head: 0.2 SEC / shot 2. Paste range: Rotation automatic replace
Technical Library | 2021-10-27 02:20:31.0
The mass flow sensor, or air flow sensor is one of the important sensors of the electronic fuel injection engine. It is installed between the air filter and the intake hose to measure the intake volume of the engine cylinder and adjust the fuel ratio according to it. The mass flow sensor converts the inhaled air flow into electrical signals and sends them to the electronic control unit (ECU). As one of the basic signals to determine the fuel injection, it is a sensor that measures the air flow of the suction engine. So if you want to test it, how should you do? Let's start it.
Technical Library | 1999-05-06 10:30:06.0
Augmentation of extended surfaces used to dissipate heat increases the overall effectiveness of a heat sink and increases the heat removed per unit volume. This amount of increase depends on the number of augmentations, air flow velocity and ...
Precision Dispensing System for Heated Dispense Applications The GPD Global MAX II is a compact; high-accuracy system designed for today’s advanced heated dispensing applications. The frame is molded from “liquid rock” which gives the system a stabl
Time Pressure Liquid Dispensing Pump with Foot switch / Dry contact A great addition to Fully Automatic Dispensing System Time pressure is a versatile method of dispensing that functions across a wide range of viscosities. This dispensing method wo
Events Calendar | Wed Jun 21 00:00:00 EDT 2017 - Sat Jun 24 00:00:00 EDT 2017 | Bangkok, Thailand
Assembly Technology Expo
Career Center | kemaman, malaysia Philippines | Maintenance,Production,Technical Support
• Conduct repairs and troubleshooting of production equipment to avoid / minimize production downtime. • Performs preventive maintenance of production equipment as defined in work procedure and according to their schedule of frequency. • C
Career Center | Cavite, Philippines | Engineering,Technical Support
I had 15 years Handling SMT Equipment.
Air Flow Measurement in Electronic Systems Air Flow Measurement in Electronic Systems Electronic circuit boards create some of the most complex and highly three dimensional fluid flows in both air and liquid. The combination of open channel
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/industrial-coating-systems/additional-product-sub-type/pressure-controlled-flow?con=t&page=13
powder coating booth facilitates uniform, constant air flow for more efficient powder recovery, enhanced collector efficiency and superior part coverage
1st Place Machinery Inc. | http://www.firstplacemachinery.com/firstplace_airvac_pcbrm12.html
Air Vac PCBRM12 Air Vac Rework Solder Fountain Serial Numbers: 1244 and 1212 Model Number: PCBRM12 X/Y Board Carrier Size
