Electronics Forum: asymtek x 1020 (Page 1 of 2)

Asymtek vs. Camalot

Electronics Forum | Tue Jul 19 15:43:37 EDT 2005 | msjohnston1

We are trying to do a dispenser comparison study between the Asymtek Axiom X1020 with DJ9000 valve and the Camalot XyflexPro system. The system will have a dual purpose for dispensing epoxy dots and underfill. I would like to have comments positive

SMT glue dispensers

Electronics Forum | Tue Nov 21 14:02:34 EST 2006 | jimmyjames

We have 2 Assembleon Opal X II machines, each with 8 head upgrades placing up to 14k CPH. We have got quote back from Essemtec, Asymtek and Camalot. The thing that is holding us back the most is our realatively small budget of $50k US. Screen prin

Solder paste dispensers question

Electronics Forum | Fri Apr 27 11:23:40 EDT 2007 | pjc

You can get reliable solderpaste dots down to 20-30mil dia. with Type 3. Accurate and repeatable dispensing machine for X-Y-Z placement of the dot is critical. Here are the leading machines: http://www.speedlinetech.com/camalot/index.aspx http://

Asymtek Millenium NSZ sensor

Electronics Forum | Sat Feb 25 12:01:28 EST 2017 | ttheis

I'm setting up a asymtek millenium m-cob style dispenser for the first time and running through the master offsets routine but when it attempts to find the needle in the nsz needle sensor it works in the x direction but when it attempts to locate in


Electronics Forum | Mon Feb 20 14:56:22 EST 2012 | acsscott

Ok, so we figured out that if the LCS is connected, we don't get the error. So, the HDLC data buss gos out and back, or is terminated in the LCS. How to remove the LCS? We try to go into maintenance screen to change the machine configuration, and

Re: Soldering to Palladium vs. Tin_Lead plated comps

Electronics Forum | Wed Feb 25 17:02:05 EST 1998 | Doug Romm

Just a comment to clarify this discussion. Typically chip caps and other passive components that use palladium plated to the end of the component are very different from the TI nickel/palladium plated IC components (leaded devices). The main di

Fixture Material

Electronics Forum | Tue Nov 07 18:56:40 EST 2006 | Steve

Thanks guys! Very helpfull info. SWAG, the manufacturer states that this material can withstand up to 350 Celsius for a short time period (around 10-20 seconds). It is my understanding that Durostone absorbs heat very very slowly like ceramic thus

QFN Thermal pad voiding

Electronics Forum | Sat May 30 01:31:49 EDT 2009 | mika

make 4 square rounded corner apertures on the ground pad and the total reduction of 20 % (80 % solder paste). Then you still be able to solder the terminals around. Don't worry to much of the void's. Just following my tips and you will be fine. The

Meridian 1020P servo wont start

Electronics Forum | Wed Jul 09 12:00:25 EDT 2014 | bobpan

You have a rather old machine that you are running....now realizing this you need to check some things. 1. Clean the scales in the x and y direction. On some of the encoders there is an led to see if its reading correctly....Usually it turns green b


Electronics Forum | Fri Jan 12 09:04:18 EST 2007 | Cal

For insurance purposes we verification... Here is a snippet from Glenbrooks website. From http://www.glenbrooktech.com Design Safety Standards The design safety standards pertaining to Industrial X-ray Inspection Systems can be found in "Code of

  1 2 Next

asymtek x 1020 searches for Companies, Equipment, Machines, Suppliers & Information


A leader in automated fluid dispensing, jetting and conformal coating. Products range from benchtop dispensers and stand-alone dispensing workstations to fully automated, in-line conveyorized systems.

Adhesives / Dispensing / Assembly / Component Packaging / Manufacturer of Assembly Equipment

2747 Loker Ave. West
Carlsbad, CA USA

Phone: 760-431-1919

SMT feeders

High Throughput Reflow Oven
Void free Reflow Soldering

ONLINE IPC Training & Certification

Orange Sticks, Wiring Aids & Probes for Soldering & Desoldering.
PCB Cleaning

Heller - Best value SMT Reflow Ovens in the market.