Electronics Forum: back on (Page 1 of 25)

Get back on the wall

Electronics Forum | Wed May 17 17:13:47 EDT 2000 | Michael Parker

The MoonMan has spoken. Everybody get back up on the wall, its been long enough that this has been "off the wall". Wish I had more Rambus chips, just got my SMT process dialed in and ran out of stock. Damn.

Tape not pulling back on components causes machine to stop

Electronics Forum | Thu Mar 14 10:49:44 EDT 2013 | babe7362000

Have others seen a higher rate of machine downtime due to the cover tape on parts not pulling back properly. We have the same problem on the Jukis and Quads. About every 3 minutes the machine stops and the operator has to pull the tape back. And in

Cover tape not always pulling back on Fuji IP-1

Electronics Forum | Thu Jun 15 03:31:26 EDT 2006 | Bert van den Berg

The cover tape on 0805, 1206 and IC reels occasionally does not pull back clear of the tape and our Fuji IP-1 stops. Although some feeders appear to be more vulnerable to this than others, is this a feeder problem or is this a material problem with

Cover tape not always pulling back on Fuji IP-1

Electronics Forum | Fri Jun 16 15:50:08 EDT 2006 | Bert van den Berg

PSA - Pressure Sensitive Adhesive? I don't know which type of tape the affected reels of parts use but it is not sticky. Thanks everyone for the comments and suggestions. There were no missing teeth on the plastic take-up reels. I have cleaned an

Cover tape not always pulling back on Fuji IP-1

Electronics Forum | Fri Jun 16 10:12:16 EDT 2006 | flipit

It it PSA tape or heat seal? Every machine I have ever used has trouble with PSA cover tape. I wish they would ban in in ROHS. 3M tells me it is the future and it will replace heat seal tape.

Tape not pulling back on components causes machine to stop

Electronics Forum | Mon Mar 18 10:33:27 EDT 2013 | babe7362000

It is not the feeders having the issue. The tape on the strip of parts does not want to pull up easily. I just wondered if anyone else out there is having the same issue. Thanks for any feedback.

Tape not pulling back on components causes machine to stop

Electronics Forum | Wed Mar 20 18:11:10 EDT 2013 | garym4569

Is the problem with the same component or manufacturer? Just for kicks, load a different component on the same feeder. Run machine in trial mode and place only that component on double sided tape. Gary

Tape not pulling back on components causes machine to stop

Electronics Forum | Wed Mar 20 12:59:10 EDT 2013 | kmots15

We had this issue with a few parts on our universal 8mm feeders. The set up was correct all mechanisms were working, even tried a new feeder. The spring in between the take up wheel and pick point just wasnt cutting it since the adheasion was too m

Cover tape not always pulling back on Fuji IP-1

Electronics Forum | Thu Jun 15 08:44:18 EDT 2006 | jdengler

Bert, The original IP feeders do a poor job of peeling the cover tape. Things to check: -All teeth present on the take-up reel -Take-up reel has even drag as it rotates (reel out of round or dirty) -Take-up reel drag is not too high (locations and

Tape not pulling back on components causes machine to stop

Electronics Forum | Thu Mar 14 17:35:39 EDT 2013 | dontfeedphils

Have you looked at the cover tape wheel on these different feeders and made sure that they are turning correctly when the feeder is advanced? There's not too many things that could be wrong, either the wheel isn't turning properly and keeping the co

  1 2 3 4 5 6 7 8 9 10 Next

back on searches for Companies, Equipment, Machines, Suppliers & Information

Count On Tools, Inc.
Count On Tools, Inc.

COT specializes in high quality SMT nozzles and consumables for pick and place machines. We provide special engineering design service of custom nozzles for those unique and odd components.

Contract Manufacturer / Manufacturer of Assembly Equipment / Manufacturer of Assembly Material / Pick and Place / Repair / Rework

2481 Hilton Drive
Gainesville, GA USA

Phone: (770) 538-0411