Technical Library: backing (Page 1 of 34)

Placement Optimisation in a Lean Manufacturing Environment

Technical Library | 2008-02-20 21:42:52.0

Tier 2 and Tier 3 EMS companies face increasing pressure from competition in low-cost manufacturing countries to produce assembled boards at lower cost, with increased complexity and to tighter deadlines. They also face an increasing amount of high-mix, small-to-mediumvolume production runs. Even OEMs find it hard to predict what products they will be manufacturing in three to five years time, driving the need to invest in highly flexible production tools that will cater to their needs over the lifetime of the equipment. This paper examines methodologies for optimising the process, improving stock control and providing greater traceability using lean manufacturing techniques.

EUROPLACER

Back to Basics – Why Clean?

Technical Library | 2011-06-28 16:10:29.0

ZESTRON America’s spring edition of ZESTRON News goes back to basics providing the latest information on the topics of cleaning in the electronics manufacturing industry.

ZESTRON Americas

Dispensing EMI Shielding Materials: An Alternative to Sputtering

Technical Library | 2020-02-26 23:24:02.0

Shielding electronic systems against electromagnetic interference (EMI) has become a hot topic. Technological advancements toward 5G standards, wireless charging of mobile electronics, in-package antenna integration, and system-inpackage (SiP) adoption are driving the need to apply more effective EMI shielding and isolation to component packages and larger modules. For conformal shielding, EMI shielding materials for exterior package surfaces have mostly been applied with a physical vapor deposition (PVD) process of sputtering, leveraging front-end packaging technologies to back-end packaging applications. However, sputtering technology challenges in scalability and cost along with advancements in dispensable materials are driving considerations for alternative dispensing techniques for EMI shielding.

Nordson ASYMTEK

An Alternative Dispense Process for Application of Catalyst Films on MEA's

Technical Library | 2008-10-01 14:02:27.0

This paper proposes an integrated system for film application process than consists of closed loop mass calibration to assure film thickness, a noncontact fast jetting process with high edge definition capable of applying films for highly selective areas and patterns. A system to obtain homogeneity of the solid-fluid mix is described and results are shared.

Nordson ASYMTEK

Increase Your Process Control and Lower Cost of Ownership

Technical Library | 2012-11-12 14:06:48.0

With consumers constantly looking for lower prices on their technology products and manufacturers trying to squeak out higher margins from their production lines, the need for process control and lower overhead costs have become even more important. One sector that is often overlooked is the hand soldering area of the factory. Many factories have been struggling with antiquated soldering systems for years. In some cases they are trying to make their investment in stations last much longer than they were designed for, or they are falsely trying to recoup their original investment ‐ all at the cost of higher operating expenses or even worse, reduced operator thru‐put.

Metcal

Surface Mount Rework Techniques

Technical Library | 1999-05-09 12:51:38.0

This Technical Note outlines, step by step, the easiest ways to remove and replace surface mounted devices, using the lowest possible temperatures. This document discusses the following topics: Removal and replacement of discrete and passive components (capacitors, resistors, SOTs), Removal of two-sided components (SOICs, SOJs, TSOPs), Removal of quad components (PLCCs, QFPs), Replacement of quad components including fine-pitched devices.

Metcal

Wedge Bonding Tool Selection

Technical Library | 2019-05-23 10:30:22.0

Increasing I/O numbers, device complexity, and product miniaturization requires high precision bonding tools, and sophisticated equipment. Careful consideration should be given to wedge geometry while selecting the tool for a fine pitch wire bonding application. Wire bonding is a process that creates an electrical connection between a die and a substrate or lead typically using gold or aluminum wire. Wedge bonding is a specific type of wire bonding that uses a wedge shaped tool to create the welds. The design of the wedge tool has changed very little over the past decade. The wire is fed at an angle through the back of the wedge. This angle is typically 30 to 60 degrees and is application dependent. Some applications require a higher feed angle due to package clearance issues. Some deep access applications require a 90 degree feed angle. In this configuration, the wire is fed through a hole in the shank of the wedge tool. Wire feed is shown in Figure 1.

ACI Technologies, Inc.

Fiber Optic Cabling

Technical Library | 2019-11-13 13:53:50.0

Fiber optic harnesses appear simple, but they have been designed to maintain all of the critical areas of aligning two fibers and minimize the losses associated with a break in the transmission path. In order to understand how the connectors overcome alignment issues, we must first understand the issues. Fiber optic communications networks use specific wavelengths of light (or colors) to transmit information through a clear fiber at high speed. They use the property of internal reflection along the fiber’s axis to contain the light and keep the optical power high enough to be detected at the receiving end.

ACI Technologies, Inc.

Hot Air vs. IR BGA Rework Stations

Technical Library | 2018-04-27 12:59:29.0

Hot Air and IR are the two main types of rework stations used by OEMs and PCB contract manufacturers today. Both have advantages and disadvantages and choosing the right one for your application requires a careful consideration of a number of factors, including your budget, your working requirements and the capabilities of your staff. In this article, we outline some of the differences between hot air and IR BGA rework stations.

Precision PCB Services, Inc

Automated Testing with Boundary Scan

Technical Library | 2019-08-19 09:46:13.0

Boundary scan is a method for testing interconnects on printed circuit boards (PCBs) or sub-blocks inside an integrated circuit. It has rapidly become the technology of choice for building reliable high technology electronic products with a high degree of testability. Due to the low-cost and integrated circuit (IC) level access capabilities of boundary scan, its use has expanded beyond traditional board test applications into product design and service.

ACI Technologies, Inc.

  1 2 3 4 5 6 7 8 9 10 Next

backing searches for Companies, Equipment, Machines, Suppliers & Information