New Equipment | Rework & Repair Equipment
Allgood Technology is equipped with a range of tools to rework and repair printed circuit assemblies to IPC-A-610 or your own company standards. Major Plant List: Metcal MFR-1351 Desoldering Station for through hole desoldering. Le
New Equipment | Industrial Automation
Contact: Nancy Lin Email:info@amikon.cn Skype:onlywnn_1 Telegram:+8618020776786 Mobile(Whatsapp): (+86)-18020776786 QQ :2851195456 Our company has many products in stock,which are immediately available.The warranty is 1 years which apply to a
Electronics Forum | Wed May 14 11:35:04 EDT 2008 | scottefiske
We produce High mix very low volume Military assemblies. So a typical order mya be for 50 pcb's, at a 5 up array. Do you work in the fab shop? Scott
Electronics Forum | Tue Jan 06 14:37:27 EST 2009 | stevek
The easiest way to prove out the absorbtion theory is to weigh the parts before wash, after wash, and after baking. You probably want to do this with the bare parts in isolation as the fab will pick up considerable moisture. Differences in weight s
Industry News | 2011-02-14 14:41:46.0
Seika Machinery, Inc., a leading provider of advanced machinery, materials and engineering services, will debut new products and features from McDry in Booth #459 at the upcoming IPC APEX EXPO, scheduled to take place April 12-14, 2011 at the Mandalay Bay Resort & Convention Center in Las Vegas.
Industry News | 2018-12-08 03:29:29.0
SMT Dictionary – Surface Mount Technology Acronym and Abbreviation
Technical Library | 2018-09-21 10:12:53.0
Moisture accumulates during storage and industry practice recommends specific levels of baking to avoid delamination. This paper will discuss the use of capacitance measurements to follow the absorption and desorption behaviour of moisture. The PCB design used in this work, focused on the issue of baking out moisture trapped between copper planes. The PCB was designed with different densities of plated through holes and drilled holes in external copper planes, with capacitance sensors located on the inner layers. For trapped volumes between copper planes, the distance between holes proved to be critical in affecting the desorption rate. For fully saturated PCBs, the desorption time at elevated temperatures was observed to be in the order of hundreds of hours. Finite difference diffusion modelling was carried out for moisture desorption behaviour for plated through holes and drilled holes in copper planes. A meshed copper plane was also modelled evaluating its effectiveness for assisting moisture removal and decreasing bake times. Results also showed, that in certain circumstances, regions of the PCB under copper planes initially increase in moisture during baking.
Technical Library | 2023-07-25 16:42:54.0
Printing solder paste for very small components like .3mm pitch CSP's and 01005 Chip Components is a challenge for the printing process when other larger components like RF shields, SMT Connectors, and large chip or resistor components are also present on the PCB. The smaller components require a stencil thickness typically of 3 mils (75u) to keep the Area Ratio greater than .55 for good paste transfer efficiency. The larger components require either more solder paste height or volume, thus a stencil thickness in the range of 4 to 5 mils (100 to 125u). This paper will explore two stencil solutions to solve this dilemma. The first is a "Two Print Stencil" option where the small component apertures are printed with a thin stencil and the larger components with a thicker stencil with relief pockets for the first print. Successful prints with Keep-Outs as small as 15 mils (400u) will be demonstrated. The second solution is a stencil technology that will provide good paste transfer efficiency for Area Ratio's below .5. In this case a thicker stencil can be utilized to print all components. Paste transfer results for several different stencil types including Laser-Cut Fine Grain stainless steel, Laser-Cut stainless steel with and w/o PTFE Teflon coating, AMTX E-FAB with and w/o PTFE coating for Area Ratios ranging from .4 up to .69.
Events Calendar | Tue Jul 18 00:00:00 EDT 2023 - Tue Jul 18 00:00:00 EDT 2023 | Chippewa Falls, Wisconsin USA
UMW Chapter In-Person Event: PCB 101 Workshop and Tour at TTM Chippewa Falls
Heller Industries Inc. | https://hellerindustries.com/delamination/
. (Some practitioners pre-bake components and boards to drive out moisture. This is not encouraged and should be a last resort as baking tends to build intermetallics as well as degrade the solderability by increasing oxidation levels
| http://etasmt.com/cc?ID=te_news_bulletin,23574&url=_print
. (Some practitioners pre-bake components and boards to drive out moisture. This is not encouraged and should be a last resort as baking tends to build intermetallics as well as degrade the solderability by increasing oxidation levels
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
1750 Mitchell Ave.
Oroville, CA USA
Phone: (888) 406-2830