S8, S10, S12 - 8, 10 or 12 top/bottom cooling zones. Heating System: Up to twelve groups of top and bottom forced hot air convection heating zones. Patented heating plates in each zone uniformly transfer heat to the PCBs using forced hot air con
E8, E10, E12 - 8, 10 or 12 top/bottom cooling zones. Heating System: Up to twelve groups of top and bottom forced hot air convection heating zones. Patented heating plates in each zone uniformly transfer heat to the PCBs using forced hot air con
Electronics Forum | Sun Sep 22 02:32:33 EDT 2013 | alexeis
Hi, If your PCB is large, you waste a time. Any picture, you takes, will be with corner distortion. I suggest you to: 1. use AOI (manually or automatically) 2. try simulation of your PCB production before real SMT production process 3. use human FAI
Electronics Forum | Mon Sep 13 04:11:27 EDT 1999 | Earl Moon
| | hello | | | | having a problem with one customers bare boards not matching my stencil apertures. i design stencils based on gerber data and reduce up to 15% on some pads. do some board houses reduce pads after receiving gerber data???why would
Used SMT Equipment | AOI / Automated Optical Inspection
Make: Vi Technology Model: 5K 3D AOI Vintage: 2017 Details: Precision XY Gantry High-Speed Linear Motors with Closed-Loop, High-Resolution Linear Encoders Automatic Conveyor Width Adjust Large Board! Max Bo
Used SMT Equipment | In-Circuit Testers
Stanford Research DS360 Function Generators The performance of a low distortion analog source and the precision of direct digital synthesis (DDS) is combined in the DS360. With less than 0.001 % total harmonic distortion (THD), 25 ppm frequency a
Industry News | 2022-10-12 08:07:17.0
I.C.T Provide SMT Production Line solutions with Automated Optical Inspection (AOI) AOI is short for Automated Optical Inspection, which is widely used in the electronics industry to check the appearance of PCBA assembly at the back end of the circuit board assembly line. The basic principle of AOI is to judge whether the object to be tested meets the standard by comparing whether there is a large difference between the object to be tested and the standard image by using image technology. AOI emits a 4-color light source to the PCBA board, which is automatically scanned by an industrial camera for catastrophic failures, such as missing components or quality defects. Therefore, the quality of AOI depends on the image imaging ability, algorithm parsing ability and image discrimination technology. I.C.T AOI has done well in these aspects.
Industry News | 2007-11-04 19:25:08.0
Aesch/Switzerland � Essemtec AG, a leading manufacturer of surface mount technology production equipment, announces that it will highlight SP900 inline printer in booths A5-277 and A5-278 at the upcoming Productronica 2007 exhibition and conference scheduled to take place November 13-16, 2007 at the New Munich Trade Fair Center in Munich, Germany.
Parts & Supplies | Assembly Accessories
After receiving the input signal of home sensor of motor related to head, it is transmitted to can master BOARD.CONVEYOR Control board receive controller The sensor input with ANC and the input of the switch on the operation panel are transmitted t
Technical Library | 2024-01-08 18:36:01.0
The following aims lie behind the investigations described: The circuit board is an integrated structure made of metal and plastic. Like most integrated components enclosed in plastic, it absorbs water. When it is rapidly heated as, for example, in soldering technology temperature processes, it is a well known fact that the water will evaporate abruptly, leading to destruction. It is therefore essential that the circuit board be dried before these soldering processes. Circuit board manufacturers are extremely hesitant at providing instructions on drying their circuit boards. Information from the ZVEI [1] should also be regarded critically. The cardinal problem is the high temperature which is recommended for baking. If this is applied, the result is often de-lamination and distortion of the circuit boards. Corrosion and the formation of intermetallic phases of the metallic surfaces are also to be expected. The following investigates whether gentle drying at 45°C or 60°C and at low relative humidity achieves the same result as baking at high temperatures. The industry provides novel dry cabinets which are suitable for rapid drying at relative humidities below one percent.
Technical Library | 2021-06-21 19:34:02.0
In this era of electronics miniaturization, high yield and low-cost integrated circuit (IC) substrates play a crucial role by providing a reliable method of high density interconnection of chip to board. In order to maximize substrate real-estate, the distance between Cu traces also known as line and space (L/S) should be minimized. Typical PCB technology consists of L/S larger than 40 µ whereas more advanced wafer level technology currently sits at or around 2 µm L/S. In the past decade, the chip size has decreased significantly along with the L/S on the substrate. The decreasing chip scales and smaller L/S distances has created unique challenges for both printed circuit board (PCB) industry and the semiconductor industry. Fan-out panel-level packaging (FOPLP) is a new manufacturing technology that seeks to bring the PCB world and IC/semiconductor world even closer. While FOPLP is still an emerging technology, the amount of high-volume production in this market space provide a financial incentive to develop innovative solutions in order to enable its ramp up. The most important performance aspect of the fine line plating in this market space is plating uniformity or planarity. Plating uniformity, trace/via top planarity, which measures how flat the top of the traces and vias are a few major features. This is especially important in multilayer processing, as nonuniformity on a lower layer can be transferred to successive layers, disrupting the device design with catastrophic consequences such as short circuits. Additionally, a non-planar surface could also result in signal transmission loss by distortion of the connecting points, like vias and traces. Therefore, plating solutions that provide a uniform, planar profile without any special post treatment are quite desirable.
S8, S10, S12 - 8, 10 or 12 top/bottom cooling zones. Heating System: Up to twelve groups of top and bottom forced hot air convection heating zones. Patented heating plates in each zone uniformly transfer heat to the PCBs using forced hot air con
E8, E10, E12 - 8, 10 or 12 top/bottom cooling zones. Heating System: Up to twelve groups of top and bottom forced hot air convection heating zones. Patented heating plates in each zone uniformly transfer heat to the PCBs using forced hot air con
Lewis & Clark | https://www.lewis-clark.com/product-tag/large-board-3d-aoi/
Large Board 3D AOI Archives - Lewis and Clark, Inc. Skip to content My Cart: $ 0.00 0 View Cart Checkout No products in the cart
| https://www.smtfactory.com/High-Speed-SMT-AOI-Machine-in-PCB-Board-Off-Line-Model-I-C-T-V8-pd48670624.html
High Speed SMT AOI Machine in PCB Board Off-Line Model I.C.T-V8 from China manufacturer - I.C.T English Français Pусский Español Português Deutsch Italiano 日本語 한국어 Tiếng Việt Türk dili Home About Us Company Profile
.gif)
