Technical Library: carrier and reel and cost (Page 1 of 2)

Status and Outlooks of Flip Chip Technology

Technical Library | 2018-11-14 21:43:14.0

Status of flip chip technology such as wafer bumping, package substrate, flip chip assembly, and underfill will be reviewed in this study. Emphasis is placed on the latest developments of these areas in the past few years. Their future trends will also be recommended. Finally, the competition on flip chip technology will be briefly mentioned.

ASM Pacific Technology

Temperature Cycling and Fatigue in Electronics

Technical Library | 2020-01-01 17:06:52.0

The majority of electronic failures occur due to thermally induced stresses and strains caused by excessive differences in coefficients of thermal expansion (CTE) across materials.CTE mismatches occur in both 1st and 2nd level interconnects in electronics assemblies. 1st level interconnects connect the die to a substrate. This substrate can be underfilled so there are both global and local CTE mismatches to consider. 2nd level interconnects connect the substrate, or package, to the printed circuit board (PCB). This would be considered a "board level" CTE mismatch. Several stress and strain mitigation techniques exist including the use of conformal coating.

DfR Solutions

Taking the LED Pick and Place Challenge

Technical Library | 2014-09-25 18:16:47.0

For the past few years there has been a shift in the Lighting Industry that has carried over to the surface mount technology assembly line. What is this shift you may ask? Well it is the LED revolution. This revolution or change in lighting has some very promising results already in practice and many more companies looking to implement the LED technology into their product portfolio's. With a number of companies looking to expand their portfolio to include LED fixtures there has been an increase in the number of companies that have started their own SMT lines, as well as a significant number of contract manufacturers to meet this new industries demands (...)This presentation will discuss some issues in the pick and place process for LEDs and presents a method to troubleshoot and resolve these issues.

Cree, Inc.

Failure Modes in Wire bonded and Flip Chip Packages

Technical Library | 2014-12-11 18:00:09.0

The growth of portable and wireless products is driving the miniaturization of packages resulting in the development of many types of thin form factor packages and cost effective assembly processes. Wire bonded packages using conventional copper lead frame have been used in industry for quite some time. However, the demand for consumer electronics is driving the need for flip chip interconnects as these packages shorten the signals, reduce inductance and improve functionality as compared to the wire bonded packages. The flip chip packages have solder bumps as interconnects instead of wire bonds and typically use an interposer or organic substrate instead of a metal lead frame (...) The paper provides a general overview of typical defects and failure modes seen in package assembly and reviews the efforts needed to understand new failure modes during package assembly. The root cause evaluations and lessons learned as the factory transitioned to thin form factor packages are shared

Peregrine Semiconductor

Influence of Nanoparticles, Low Melting Point (LMP) Fillers, and Conducting Polymers on Electrical, Mechanical, and Reliability Performance of Micro-Filled Conducting Adhesives for Z-Axis Interconnections

Technical Library | 2007-11-01 17:16:07.0

This paper discusses micro-filled epoxy-based conducting adhesives modified with nanoparticles, conducting polymers, and low melting point (LMP) fillers for z-axis interconnections, especially as they relate to package level fabrication, integration,

i3 Electronics

A High Performance and Cost Effective Molded Array Package Substrate

Technical Library | 2010-11-18 19:19:50.0

In this article we present both a relatively new and innovative family of packages that is suitable for medium pin count needs and an innovative method for fabricating the substrates for such a package. With respect to lead count, this packaging family is

EoPlex Technologies, Inc.

Reliability of Embedded Planar Capacitors under Temperature and Voltage Stress

Technical Library | 2015-05-21 18:46:31.0

In this work the reliability of an embedded planar capacitor laminate under temperature and voltage stress is investigated. The capacitor laminate consisted of an epoxy-BaTiO3 composite sandwiched between two layers of copper. The test vehicle with the embedded capacitors was subjected to a temperature of 125oC and a voltage bias of 200 V for 1000 hours. Capacitance, dissipation factor, and insulation resistance were monitored in-situ. Failed capacitors exhibited a sharp drop in insulation resistance, indicating avalanche breakdown. The decrease in the capacitance after 1000 hours was no more than 8% for any of the devices monitored. The decrease in the capacitance was attributed to delamination in the embedded capacitor laminate and an increase in the spacing between the copper layers.

CALCE Center for Advanced Life Cycle Engineering

Novel Probing Concepts for Mass-Production Tests: Design and Challenges

Technical Library | 2012-06-15 00:43:47.0

First published in the 2012 IPC APEX EXPO technical conference proceedings. The world of spring-loaded test probes and special probes for in-circuit and functional tests have grown tremendously over the past few years. Ever increasing demands for electro

INGUN Pruefmittelbau GmbH

Development of a Design & Manufacturing Environment for Reliable and Cost- Effective PCB Embedding Technology

Technical Library | 2011-10-06 13:59:04.0

The desire to have more functionality into increasingly smaller size end products has been pushing the PCB and IC Packaging industry towards High Density Interconnect (HDI) and 3D Packaging (stacked dies, embedded packaged components). Many companies in the high-end consumer electronics market place have been embedding passive chip components on inner PCB and IC Packages for a few years now. However, embedding packaged components on inner layers has remained elusive for the broader market due to lack of proper design tools and high cost of embedding components on inner layers (...) This paper will highlight several key industrialization aspects addressed in the frame of the European funded FP7 HERMES* project to build a manufacturing environment for products with embedded components. The program entered its third year and is now dealing with the manufacturing of functional demonstrators as an introduction to industrialization.

Cadence Design Systems, Inc.

Overview of Quality and Reliability Issues in the National Technology Roadmap for Semiconductors

Technical Library | 1999-08-05 10:27:43.0

This document is an update to the 1994 Quality and Reliability Roadmap issued in support of the 1994 National Technology Roadmap for Semiconductors. This report revisits the challenges, constraints, priorities, and research needs pertaining to quality and reliability issues. It also provides key project proposals that must be implemented to address concerns about reliability attainment and defect learning. An expanded section on test-to-test, diagnostics, and failure analysis; an edited version of the Product Analysis Forum Roadmap; and an appendix containing a draft report highlighting reliability issues is included.

SEMATECH

  1 2 Next

carrier and reel and cost searches for Companies, Equipment, Machines, Suppliers & Information

MSD Dry Cabinets

MSD Dry Cabinets
Jetting Pump for Integration

Easily dispense fine pitch components with ±25µm positioning accuracy.
NPM D3 Machine

Best Reflow Oven
https://pages.zestron.com/zestron-analytical-support-services

World's Best Reflow Oven Customizable for Unique Applications
msd storage

무플럭스 리플로우 솔더링을 위한 포름산 리플로우 오븐