Technical Library | 2023-09-13 13:07:16.0
Pneumatic stencil cleaning machines are a great way to improve the efficiency and effectiveness of your stencil cleaning process. These machines use compressed air to remove contaminants and debris from stencils, which can cause defects and reliability issues.
Technical Library | 2023-09-13 13:10:06.0
Pneumatic stencil cleaning machines are a great way to improve the efficiency and effectiveness of your stencil cleaning process. These machines use compressed air to remove contaminants and debris from stencils, which can cause defects and reliability issues.
Technical Library | 2021-09-02 08:17:07.0
We are a professional manufacturer of PCB depaneling machines, which is workable for all boards, including flex and regid boards, v-scored boards and routed boards. Laser pcb depaneling is non-contact way without mechanical stress,this solution is good for modern precision PCB depaneling. It has below advantages: 1. No dust The production environment of the circuit board industry is carried out in the dust-free workshop. The traditional pcb depaneling equipment, such as blade moving type machine, will inevitably produce residues and micro powder, which will pollute the 10000 and 1000 class dust-free workshops and affect the conductivity of products. The UV laser PCB cutting machine is a vaporization processing process, which will not produce dust and is conducive to the conductivity of the product. 2. High cutting precision The processing gap of high-precision traditional processing equipment can not reach the gap width of less than 100 microns, which will cause certain damage to the lines on the edge or PCBA circuit board containing components. The focus spot of the laser cutting machine is small, and the ultraviolet cold processing mode has little thermal impact on the edge of the circuit board. The cutting position accuracy is less than 50 microns, and the cutting size accuracy is less than 30 microns, which will not affect the edge of the circuit board, and the precision is high. 3. No stress Traditional processing methods generally have V-grooves, which will cause certain damage to the board in the manufacturing process. The UV laser PCB cutting machine can directly cut the bare board without making V-grooves. In addition, the traditional processing methods directly use tools to act on the circuit board, especially the stamping method has a great impact on the circuit board, which is easy to cause board deformation. The laser cutting machine is a non-contact processing mode, which acts on the surface of the material through the high-energy beam, which will not cause the influence of stress and the deformation and damage of the circuit board. 4. For special-shaped cutting, it is easy to automate The UV laser PCB cutting machine can cut for any shape without replacing any props and fixtures, and without steel mesh. The same equipment can meet special-shaped and straight-line cutting, which is easy to realize assembly line automatic production and high flexibility. It is easy to improve production efficiency and save production process and production cycle. In particular, it can quickly and efficiently meet the needs of rapid proofing, directly import the drawing, and then locate the cutting. 5. High compatibility The UV laser PCB cutting machine can process the materials around the circuit board, such as PCB, FPC, covering film, pet, reinforcing board, IC, ultra-thin metal cutting, etc. it has strong practicability, is compatible with the processing of a variety of materials, is easy to operate, can be imported into the drawing, does not need to adjust any mechanical parts, and is easy to operate and maintain. 6. Good cutting edge effect The cutting edge is smooth and neat without burr. It can be processed and formed directly according to the size of the drawing, which is conducive to improving the yield of the product. It can be directly installed into the subsequent process without further processing. For more details about UV laser depaneling, please feel free to contact us. www.pcbdepanelingrouter.com
Technical Library | 2022-12-05 16:22:13.0
This paper reviews the possible causes and effects for no-fault-found observations and intermittent fail- ures in electronic products and summarizes them into cause and effect diagrams. Several types of inter- mittent hardware failures of electronic assemblies are investigated, and their characteristics and mechanisms are explored. One solder joint intermittent failure case study is presented. The paper then discusses when no-fault-found observations should be considered as failures. Guidelines for assessment of intermittent failures are then provided in the discussion and conclusions.
Technical Library | 2012-12-14 14:17:56.0
This article provides practical and affordable Design-for- Test (DFT) and Design-for-Inspection (DFI) methods that will have a positive impact on product costs, yield, reliability, and time-to-market. The properties of testability (including controllability and observability) will be analysed as they relate to analogue and digital design rules and their cause/effect, as well as the electrical and physical characteristics of proper PCB design.
Technical Library | 2021-07-27 14:57:18.0
It should be noted that this is an overview paper that represents the early stages of an ongoing investigation into the causes and effects between conductive anodic filament (CAF) formation and printed wiring board (PWB) material damage. Our belief is that certain or specific types of material damage can increase the propensity for CAF formation. The preliminary data collected suggests is that there is no statistical correlation between the general definition of material damage (cohesive failure) and CAF. The resulting dichotomy is that we find no CAF failures in some coupons that have obvious material damage and we find CAF failures in coupons that don't exhibit material damage.
Technical Library | 2019-04-11 05:59:57.0
Are your MSD safely stored? As humidity is found to be one of the key reasons for rejected products, many manufacturers are taking measures to control the humidity to increase their production efficiency and save the cost. In the industries of semi-conductor and electronics, the key section in which the rejected products are most probably to be made is that during the heating process of SMT, the IC(e.g.,PBGA,BGA,or TQFD) is likely to crack and thus cause non-effective welding because of the humidity. Climatest Symor® auto dry cabinet is the best solution to avoid the cracking and non#2;effective welding by dehumidifying the surface of your components. The dry unit can be used for 20 years without replacement,and controller is calibration free within 5 years.We attach dry cabinet application with different humidity range,welcome to download.
Technical Library | 2015-08-20 15:51:08.0
Temperature and Humidity on Selective Conformal Coating It is well known that selective conformal coating on printed circuit board (PCB) assemblies provides unparallel protection for PCB’s. Nevertheless, concentrated conditions of humidity, water, and high temperatures can have negative effects on the conformal coating itself causing it to fail and become inapt for its intended purpose. Taking this into consideration, it is prudent to choose the right type of conformal coating that best suits the application and environmental conditions under which an assembly is likely to undergo in use. The proper conformal coating will significantly reduce the likelihood of failure/rejection, saving both valuable time and money for any manufacturing process.
Technical Library | 2011-03-16 20:05:15.0
Fiber weave effect is becoming more of an issue as bit rates continue to sore upwards to 5GB/s and beyond. Due to the non-homogenous nature of printed circuit board laminates, the fiberglass weave pattern causes signals to propagate at different speeds wi
Technical Library | 2022-07-11 09:24:48.0
The change of squeegee pressure has a significant impact on printing. Too small pressure will make the solder paste unable to effectively reach the bottom of the stencil opening and not be well deposited on the pad. Too much pressure will cause tin The paste is printed too thin and can even damage the stencil.
