Technical Library | 2023-09-07 14:54:10.0
A global manufacturer of a broad line of electronic interconnect solutions worked with us to dispense conductive adhesive EpoTek H20E-FC. EpoTek H20E-FC is a two-component, electrically conductive, snap curing epoxy for photovoltaic thin film module stringing, semiconductor packaging and PCB circuit assembly. The primary goal was filling a rectangular cavity on a connector. The epoxy needed to fill the connector to the top of the walls in less than three seconds.
Technical Library | 2019-10-16 10:20:25.0
A major goal of the development of advanced packaging technology is to reduce the size, weight, and power consumption of electronics components using state-of-the-art commercial technologies. One of the novel concepts involves the use of all three spatial dimensions when designing and producing new systems. In the past, electronic structures tended to be two dimensional in nature. Generally speaking, individually packaged integrated circuit (IC) dies were interconnected on printed circuit boards. Techniques such as die and package stacking naturally contribute to a reduction of the spatial footprint of any given electronic system design.
Technical Library | 2012-12-17 22:05:22.0
Package on Package (PoP) has become a relatively common component being used in mobile electronics as it allows for saving space in the board layout due to the 3D package layout. To insure device reliability through drop tests and thermal cycling as well as for protecting proprietary programming of the device either one or both interconnect layers are typically underfilled. When underfill is applied to a PoP, or any component for that matter, there is a requirement that the board layout is such that there is room for an underfill reservoir so that the underfill material does not come in contact with surrounding components. The preferred method to dispensing the underfill material is through a jetting process that minimizes the wet out area of the fluid reservoir compared to traditional needle dispensing. To further minimize the wet out area multiple passes are used so that the material required to underfill the component is not dispensed at once requiring a greater wet out area. Dispensing the underfill material in multiple passes is an effective way to reduce the wet out area and decrease the distance that surrounding components can be placed, however, this comes with a process compromise of additional processing time in the underfill dispenser. The purpose of this paper is to provide insight to the inverse relationship that exists between the wet out area of the underfill reservoir and the production time for the underfill process.
Technical Library | 2015-09-03 18:06:11.0
While the density of chip-to-chip and chip-to-package component interconnections increases and their size decreases the ease of manufacture and the interconnection reliability are being reduced. This paper will introduce the use of embedded fibers in the interconnections as a means of addressing these issues.
Technical Library | 2001-04-24 10:47:02.0
Board-level circuits today routinely run at speeds of 100 MHz or more and are composed of dozens of complex interacting VLSI components. To design such circuits in a timely and correct manner it is necessary to pay close attention to circuit timing early in the design cycle. At fast clock speeds, managing component and interconnect propagation delay becomes a key aspect of circuit design. It is imperative that the critical paths on a circuit and the slack available for interconnect delay consumption be identified early, and drive subsequent stages in the design flow.
Technical Library | 2008-01-24 21:42:39.0
Although many through-hole components are being replaced by their surface mount (SMT) counterparts, printed circuit boards (PCBs) are still being designed with both types of components. Often, there are interconnect hardware, displays, or other components that cannot withstand the exposure to the high temperature involved in the wave soldering process. They are generally soldered by hand. The challenge is to determine the optimal method manufacturers can use to solder these boards populated with mixed technology.
Technical Library | 2020-09-16 21:24:56.0
Additive manufacturing processes typically used for mechanical parts can be combined with enhanced technologies for electronics production to enable a highly flexible manufacturing of personalized 3D electronic devices. To illustrate different approaches for implementing electrical and electronic functionality, conductive paths and electronic components were embedded in a powder bed printed substrate using an enhanced 3D printer. In addition, a modified Aerosol Jet printing process and assembly technologies adapted from the technology of Molded Interconnect Devices were applied to print circuit patterns and to electrically interconnect components on the surface of the 3D substrates.
Institute for Factory Automation and Production Systems (FAPS)
Technical Library | 2022-01-12 19:26:19.0
Autonomous vehicles have the potential to revolutionize the automotive industry and are gaining immense attention from academia as well as industry. However, facets of autonomous vehicle systems related to the interconnection of independent components pose vulnerabilities to the system as a whole. These vulnerabilities aren't guaranteed to be solved by traditional security methods. Blockchain technology is a powerful tool that can aid in improving trust and reliability in such systems.
Technical Library | 2021-12-02 01:48:53.0
Some mechanical and assembly productions of existing companies of the Industry 3.0 and mechanical and assembly productions of perspective companies of the Industry 4.0 are described. The basic components of a smart factory and their interconnection to organize a production activity using humanless and paperless technologies are defined. A comparison analysis of parts and blanks movement to complete route sheet of the item manufacturing (radio and electronic item designing) in the companies of the Industry 3.0 and Industry 4.0 is given. The components of a digital item designing company to be created and implemented in the industry at first hand are defined.
University of Information Technologies, Mechanics and Optics [ITMO University]
Technical Library | 2013-11-27 16:54:01.0
The need in complexity for microwave space products such as active BFNs (Beam Forming Networks) is increasing, with a significantly growing number of amplitude / phase control points (number of beams * numbers of radiating elements). As a consequence, the RF component’s package topology is evolving (larger number of I/Os, interconnections densification ...) which directly affect the routing and architecture of the multilayer boards they are mounted on. It then becomes necessary to improve the density of these boards (...) This paper will present the work performed to achieve LCP-based high density multilayer structures, describing the different electrical and technological breadboards manufactured and tested and presenting the results obtained.
