Quality precision die bonding / pick and place tools, collets, ejector pins, wire clamps
Suppliers Of Microelectronics & PCB Assembly Equipment & Materials, including die bond, wire bond & test & SMT screen printers & pick and place systems.
New Equipment | Curing Equipment
A Pressure Cure Oven (PCO), or Autoclave, is used to minimize voiding and increase adhesion strength for bonding processes typically used in die attach and underfill applications. PCO pressurizes air into a rigid vessel and heats & cools with
New Equipment | Design Services
The manufacturing factory at ACI includes a clean room, power electronics assembly and packaging laboratory. This specialized facility aids in the development of manufacturing and assembly technologies that can exploit the advantages of advanced mat
Electronics Forum | Tue Jun 04 19:33:16 EDT 2002 | rob_thomas
Dave's estimation is pretty conservative but there is a lot of equipment out there and a lot of people happy to make a sale.Implementing both mentioned processes it's difficult and time consuming .Even if you get good training from whoever sells you
Electronics Forum | Mon May 07 22:29:52 EDT 2001 | davef
4 wire per sec ... you figure how many you need] Encapsulation ~$120K for a dispenser [10 sec per die ... you figure how many you need] plus a cure oven ~$100k Throw in a another ~$100k for marking and cleaning Check the September 2000 SMTnet New
Used SMT Equipment | X-Ray Inspection
Very Nice Nicolet Xray Machine For Sale The system is complete and in good working condition See attached pictures and information below Nicolet Imaging Systems Model Number: NXR-1500 Serial Number: 0150011 Year 2000 Variable Speed Joystick
Used SMT Equipment | General Purpose Equipment
ASM MS899-DL Wafer Mapping Die Sorter Machine is in like new condition! Serial Number: MS899DL-01817-0402 Model Number: MS899-DL Year 2008 August Cycle Time: 175 ms XY Placement: +/- 1.5 mil Die Rotation: +/- 3 degrees Collect type: Surfa
Industry News | 2003-07-02 08:54:26.0
A novel unreinforced, thermally conductive, pressure sensitive adhesive tape delivers very high bond strength to low-energy surfaces.
Industry News | 2014-09-30 18:49:51.0
MIRTEC, “The Global Leader in Inspection Technology,” announces that it was awarded a 2014 Global Technology Award in the category of LED Production Equipment for its MV-9XP LED Package Inspection System.
Technical Library | 2019-05-21 17:34:08.0
Flip chip components have been gaining popularity in the electronics industry since their introduction in the 1960s. Advances in attach methods and adhesives, as well as the drive for smaller and faster electronic devices made the technology take off. The basic premise of the flip chip is that the chip (semiconductor device) is mounted flipped from the traditional position. The traditional method of mounting a die is to mount it on a lead frame with the circuit and bond pads face up. The bond pads then receive a bond wire which then connects to the proper lead on the lead frame. Flip chips are mounted face down onto a substrate using small bumps on the bond pads to make direct electrical connection to their respective pads on the substrate. Stay tuned for more information on attachment techniques next month. This article will focus on how to rework flip chips.
Technical Library | 2020-11-09 16:59:53.0
A customer contacted ACI Technologies regarding a high failure rate of their assemblies. They provided assemblies to be X-rayed and inspected for the purpose of identifying any process related issues such as (but not limited to) solder and assembly workmanship and evidence of damage due to moisture related problems during reflow (a.k.a. "popcorning"). Moisture damage usually appears as physical damage to the component. The first indication of moisture damage would be externally observable changes to the package in the form of bulging or fractures to the outer surface of the component, an example of which is shown in Figure 1. Internally observable indicators of moisture damage typically include fractures to the die inside the package and lifted or fractured wire bonds. These conditions would be apparent during transmissive X-ray inspection. Another symptom of moisture related damage would be inconsistent solder joint sizes that result from package deformation during the liquidus phase of the reflow process. None of these indicators of moisture related damage were present on the customer samples.
General curing, die attach curing, underfill curing, film & tape bonding, wafer laminating.
ACI Technologies Inc. (ACI) is a scientific research corporation dedicated to the advancement of electronics manufacturing processes and materials for The Department of Defense and industry. This video provides an overview of our commercial service
Events Calendar | Mon Apr 23 00:00:00 EDT 2018 - Thu Apr 26 00:00:00 EDT 2018 | Shanghai, China
SMTA China East Conference 2018
Events Calendar | Wed Sep 12 00:00:00 EDT 2018 - Sun Sep 30 00:00:00 EDT 2018 | ,
Improving Material Dispensing Yield in Manufacturing Applications
Career Center | Milwaukee, Wisconsin USA | Engineering
Responsible for all Wire and die bond process within this fast growing Microelectronics company. Company is constantly upgrading equipment and processes to compete in the fiber optics arena. Company will either hire fulltime or a contract worker who
Career Center | Greenville, South Carolina USA | Engineering
Process engineer with flip chip and die bonding experience is needed for a well-established company in South Carolina. This is a new position. Relocation is available. BS is required. Send resume as a Word attachment to sfrederick@connectipro.com.
Career Center | SanPedro, Philippines | Maintenance,Production
Set-up Equipment machine and ensure its proper operation for costumer satisfaction. Carry out all Proactive Maintenance (PM) tasks such as predictive maintenance, preventative maintenance, failure finding maintenance and calibration maintenan
Career Center | ORLANDO, Florida USA | Engineering,Maintenance,Production,Technical Support
Manufacturing tech/eng for a contract manufacture for 10+ years. Been working in the SMT industry for a total of 20yrs. Have done everything from operator to process work. Most familiar with Assembleon, MPM, DEK, BTU,Electrovert, SLIM-KIC, SUPER-MOLE
SMTnet Express, May 8, 2014, Subscribers: 22716, Members: Companies: 13872, Users: 36158 Challenges in Bare Die Mounting Larry Gilg, Die Products Consortium Bare die mounting on multi-device substrates has been in use in the microelectronics
| https://www.eptac.com/faqs/ask-helena-leo/ask/gold-wire-bond-failing-pull-test
) at die. (a-4) Failure in bond (interface between wire and metallization) at substrate, package post, or other than die. (a-5) Lifted metallization from die. (a-6
1st Place Machinery Inc. | http://www.firstplacemachinery.com/firstplace_asm_MS899.html
: MS899-DL Year 2008 August Cycle Time: 175 ms XY Placement: +/- 1.5 mil Die Rotation: +/- 3 degrees Collect type: Surface pick type Pick/Bond Force: 40 - 250 g (adjustable
