Industry Directory | Manufacturer
2 component resin meter mix dispense system 2 component glue potting machine 2 component ab glue dispenser ab resin dosing machine, ab resin mixing machine, Potting and encapsulation machine
Time Pressure Liquid Dispensing Pump with Foot switch / Dry contact A great addition to Fully Automatic Dispensing System Time pressure is a versatile method of dispensing that functions across a wide range of viscosities. This dispensing method wo
Volumetric Dispense Pump - PCD Technology revolutionizes how you dispense and how you perceive dispensing. PCD - Progressive Cavity Displacement PCD is a continuously volumetric dispense pump based on the Progressive Cavity principle. PCD technolog
Electronics Forum | Thu Jan 06 09:31:39 EST 2011 | davem
Hey Guys, I'm interested in installing a new drip pan under our Trek Westek Triton IV Aqueous Cleaner. I'm looking for a fabricator in the Greater Boston/North Shore Massachusetts area. We haven't yet decided on stainless or plastic. Any suggestio
Electronics Forum | Mon Oct 27 05:35:33 EDT 2014 | grahamcooper22
Are you doing PIN IN PASTE (intrusive reflow) ? If so, then paste can be dripping through the pcb holes and onto the oven bottom heaters / baffles . Or, if any of the SMT pads have vias in them, paste may drip through them if they are not sealed. Whe
Used SMT Equipment | Screen Printers
2.0 Cmk @ ± 12.5 μm (± 6 sigma) System alignment capability > 2.0 Cmk @ ± 25 μm (± 6 sigma) Optimum core cycle time 8 seconds Substrate size 50 mm (X) x 40.5 mm (Y) to 620 mm (X) x 508.5 mm (Y) Operating System Windows 7 Embe
Used SMT Equipment | Board Cleaners
• Chemical isolation package • Torrid zone dryers • 480v/ 60Hz • Drip tray • 20” process width • Checkmate conveyor • Dual Hurricane nozzles • 15hp Hurricane rinse and wash jets • 15hp Torrid Zone Dryer/ plus (2) 3ph blowers and (1) 5hp blow
Industry News | 2016-07-16 13:32:29.0
Advanced dispense technology is available for integration into your dispensing system. Continuously Volumetric, drip-and-drool free dispense technology can now be retrofitted into your dispense robot. GPD Global's Volumetric PCD pumps ensure the success of applications like underfill, LED encapsulation, solder mask, silicones, conductive ink, conformal coatings, and more. Improve your throughput and yields by retrofitting a Volumetric PCD Pump into your dispense system to simplify the dispense process.
Industry News | 2013-06-10 17:08:51.0
GPD Global will exhibit in Stand #6275 in the North Hall at the 2013 SEMICON West exhibition & conference. Representatives from GPD Global will exhibit the company's new technology related to fine line and nano-shot dispensing, particularly related to vertical interconnect technology.
.jpg)
Parts & Supplies | Chipshooters / Chip Mounters
137500 PRESSURE REGULATOR 137338 LINEAR RAIL, 119842 COMP. SPRING LC-035F-8-MW 119835 SEAL MOUNTING PIN 119834 MOTOR MOUNTING BRACKET 119473 EFD HOUSING - PASTE DISPENSER 119472 RETAINING STUD DRIP TRAY 119268 NOZZLE (DIA. 5mm)
.jpg)
Parts & Supplies | Chipshooters / Chip Mounters
156978 STOPPER ARM 156476 248/249/260 ADAPTER, IMP. SCALE 156475 248/249/260 ADAPTER, METRIC SCALE 156442 CHASE ADAPTER, SHAFT 156441 CHASE ADAPTER, STRIP 156284 POINTER 156283 GUIDE BLOCK 156280 E-CLIP D1500 0080 156279 INS
Technical Library | 2016-02-11 18:26:43.0
Although reflow ovens may not have been dramatically changed during the last decade the reflow process changes step by step. With the introduction of lead-free soldering not only operation temperatures increased, but also the chemistry of the solder paste was modified to meet the higher thermal requirements. Miniaturization is a second factor that impacts the reflow process. The density on the assembly is increasing where solder paste deposit volumes decreases due to smaller pad and component dimensions. Pick and place machines can handle more components and to meet this high through put some SMD lines are equipped with dual lane conveyors, doubling solder paste consumption. With the introduction of pin in paste to solder through hole components contamination of the oven increased due to dripping of the paste.
Technical Library | 2019-05-08 01:46:32.0
IPX9K Rain Spray Test Chamber(high Pressure high temperature water jet) simulates the use of pressure washer steam cleaning onto the enclosure, It is recognised as the harshest of all ingress protection tests. However the requirement is becoming more prevalent across many industries. Test method for IPX9K : Make sure the water temperature inside the water tank +80°C, water flow rate with 14L-16L per min, water pressure: 8000 Kpa -10000 Kpa (80–100 bar) at distance of 100mm~ 150mm, The test duration is 30 seconds in each of 4 angles, total spray testing time is 2 minutes. IPX9K rain test chamber applicable standards: IEC 60529 – Degrees of protection provided by enclosures (IP Code).Here is working principle in picture. Application: It is mainly suitable for testing the performance of shell and seal of electrical and electronic parts, automobile parts and seals under the condition of dripping rain to prevent Rain Water from permeating or working after drizzling.
http://www.gpd-global.com No drip no drool across a wide range of fluid viscosities (low-to-mid and low-to-high). No manual adjustment to compensate for pump variability. Truly Volumetric PCD Pumps for total control of dispensing fluids. Ability to
Time Pressure Liquid Dispensing Pump with Foot switch / Dry contact A great addition to Fully Automatic Dispensing System Time pressure is a versatile method of dispensing that functions across a wide range of viscosities. This dispensing method wo
Career Center | Thanjavur, India | Production,Quality Control,Technical Support
work in one year and above Quality engineer in sanmina,current work in SMT Technical engineer in coimbatore
. Flux accumulation and dripping inside the oven not
Heller Industries Inc. | https://hellerindustries.com/wp-content/uploads/2018/07/Heller-Frost-and-Sullivan-2013-Award.pdf
solutions ahead of the competition. Handling of flux is among the top challenges for customers. Flux is a component that comes from solder paste. It can also leave residue that drips on the circuit board and within the oven. The company has developed a
