Electronics Forum: electrovert 10-12 zone thermocoupler (Page 1 of 1)

Electrovert oven zone

Electronics Forum | Thu Feb 16 20:55:57 EST 2017 | youngbuck

Was wondering if anybody has experience a zone that will not get up to temperature. I changed the Solid state relay, made sure the thermocouple is working. The only thing I can think of is the bottom heater panel has a corroded/broken wire which is a

Looking for repair/service company for electrovert bravo 8 reflow oven

Electronics Forum | Sat Jul 01 00:20:08 EDT 2017 | aemery

Kelly, it's been a long while since I repaired a BRAVO. The machine was a little unique as far as Electrovert ovens go. I am pretty sure that it is the only Speedline model that integrated a PLC. Loved the OMNI's, not so much with the Bravos. I a

Thermo runaway

Electronics Forum | Wed Jan 24 22:38:45 EST 2007 | electrovert

Hello, My first time post up here. I have a problem with thermo runaway on upper zone #5 on the Omni 10 Electrovert. We changed the thermocouple #5 but the problem came back up. We swapped Sensoray board 8 and 9, swapped board #3 (T/C interface boar

Thermo runaway

Electronics Forum | Thu Jan 25 15:39:07 EST 2007 | electrovert

We swapped the solid state relay for zone 5 bottom to zone 5 top but the problem came up once a while. As for noise protection, there are jumpers at E1 to E8 and E9 to E16. They are hardware filters and prevent noise spikes from affecting thermocoupl

Electrovert Omniflo

Electronics Forum | Fri Nov 02 14:22:20 EDT 2012 | marcelll

Hi, I'm looking for a copy of the Omniflo oven firmware. I'm talking about the model running under Win NT. Oven vintage is 1999-2001. Our oven is a 7 zones but I thing there's only one firmware for all the Omniflo ( 7, 10 12 zones . The original was

Electrovert Omniflo 7 reflow ovens

Electronics Forum | Thu Aug 30 11:59:00 EDT 2001 | Spanky

Hey all, I have 3 questions about reflow. Hopefully someone can help me. 1. I am having a problem. I set the peak at 230 and my mole thermocouples are telling me the temp in that zone gets to 237. How is this possible even if the thermocouple

Electrovert Omniflo-7 Reflow Oven VS Lead-Free

Electronics Forum | Thu Feb 10 16:45:36 EST 2005 | pjc

It all depends on what type of board you need to solder. If your boards are small in size and low thermal mass and your conveyor speed requirments are normal, then I'd say the OmniFlo 7 will do the job. It has a max zone temp setting of 280C. The cur

Pallet absorb thermal heat : compensate by higher deg-C?

Electronics Forum | Sun Jun 10 12:30:10 EDT 2001 | procon

Is this a Convection Oven or IR? If convection, you can increase the air velocity in the zones if the oven has this ability. You should do as Dave has explained. If you must use pallets when reflowing your components, you need to profile in the same

Re: Best reflow temperature

Electronics Forum | Thu Sep 16 12:06:29 EDT 1999 | Scott S. Snider

| | | Hi, | | | | | | Can someone pls suggest to me the best reflow temperature setting | | | for a force air convection oven. The details is as follow. | | | 1) Heller 1700s | | | 2) 12 zone---6 top and 6 bot | | | 3) Solder paste --- Qualitek 691


electrovert 10-12 zone thermocoupler searches for Companies, Equipment, Machines, Suppliers & Information