Technical Library | 2023-01-17 17:27:13.0
Reflow profile has significant impact on solder joint performance because it influences wetting and microstructure of the solder joint. The degree of wetting, the microstructure (in particular the intermetallic layer), and the inherent strength of the solder all factor into the reliability of the solder joint. This paper presents experimental results on the effect of reflow profile on both 63%Sn 37%Pb (SnPb) and 96.5%Sn 3.0%Ag 0.5%Cu (SAC 305) solder joint shear force. Specifically, the effect of the reflow peak temperature and time above solder liquidus temperature are studied. Nine reflow profiles for SAC 305 and nine reflow profiles for SnPb have been developed with three levels of peak temperature (230 o C, 240 o C, and 250 o C for SAC 305; and 195 o C, 205 o C, and 215 o C for SnPb) and three levels of time above solder liquidus temperature (30 sec., 60 sec., and 90 sec.). The shear force data of four different sizes of chip resistors (1206, 0805, 0603, and 0402) are compared across the different profiles. The shear force of the resistors is measured at time 0 (right after assembly). The fracture surfaces have been studied using a scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS)
Technical Library | 2017-09-14 01:21:52.0
The electronics industry is experiencing a renaissance in semiconductor package technology. A growing number of innovative 3D package assembly methodologies have evolved to enable the electronics industry to maximize their products functionality. By integrating multiple die elements within a single package outline, product boards can be made significantly smaller than their forerunners and the shorter interconnect resulting from this effort has contributed to improving both electrical performance and functional capability. (...) This paper outlines both positive and negative aspects of current 3D package innovations and addresses the challenges facing adopters of silicon and glass based interposer fabrication. The material presented will also reference 3D packaging standards and recognize innovative technologies from a number of industry sources, roadmaps and market forecasts.
Technical Library | 2016-04-21 14:10:55.0
The world of electronics continues to increase functional densities on products. One of the ways to increase density of a product is to utilize more of the 3 dimensional spaces available. Traditional printed circuit boards utilize the x/y plane and many miniaturization techniques apply to the x/y space savings, such as smaller components, finer pitches, and closer component to component distances.This paper will explore the evolution of 3D assembly techniques, starting from flexible circuit technology, cavity assembly, embedded technology, 3 dimensional surface mount assembly, etc.
Technical Library | 2020-10-14 14:49:14.0
In this study, the modification of an epoxy matrix with different amounts of cube-like and rod-like CaCO3 nanoparticles was investigated. The effects of variations in the morphology of CaCO3 on the mechanical properties and thermal stability of the CaCO3/epoxy composites were studied. The rod-like CaCO3/epoxy composites (EP-rod) showed a higher degradation temperature (4.5 _C) than neat epoxy. The results showed that the mechanical properties, such as the flexural strength, flexural modulus, and fracture toughness of the epoxy composites with CaCO3 were enhanced by the addition of cube-like and rod-like CaCO3 nanoparticles. Moreover, the mechanical properties of the composites were enhanced by increasing the amount of CaCO3 added but decreased when the filler content reached 2%. The fracture toughness Kic and fracture energy release rate Gic of cube-like and rod-like CaCO3/epoxy composites (0.85/0.74 MPa m1/2 and 318.7/229.5 J m
Technical Library | 2023-10-09 16:10:02.0
This document provides high-level PCB design, sensor mounting, and handling guidelines for TDK IMU devices, which incorporate a combination of gyroscopes and accelerometers. Each sensor has specific requirements to ensure the highest performance in a finished product. For a layout assessment of your design, including placement and estimated temperature disturbances, please contact TDK. The TDK IMU devices discussed in this document (ICM-40607x, ICM-40608, ICM-42xxx, ICM-43xxx, and ICM-45xxx products) consist of 3-axis MEMS gyroscopes and 3-axis MEMS accelerometers.
Technical Library | 2023-03-13 19:35:47.0
Translational Research in Additive Manufacturing at GTMI * Additive manufacturing/3D printing process and equipment development (e.g., metal, polymer and composites part manufacturing) * Computational modeling and simulation of additive manufacturing/printed electronics processes * Advanced materials development for additive manufacturing/printed electronics * Application development and demonstration of additive manufacturing/printed electronics
Technical Library | 2012-01-19 19:14:49.0
The history of multilayered, three-dimensional monolithic microwave integrated circuit (3-D MMIC) technology is described here. Although significant researches were carried out in the second half of 1990’s, still there were many twists and turns before an
Technical Library | 2020-07-02 13:16:32.0
Principle of shielding 1 The principle of shielding is creating a conductive layer completely surrounding the object you want to shield. This was invented by Michael Faraday and this system is known as a Faraday Cage. 2 Ideally, the shielding layer will be made up of conductive sheets or layers of metal that are connected by means of welding or soldering, without any interruptions. The shielding is perfect when there is no difference in conductivity between the used materials. When dealing with frequencies below 30 MHz, the metal thickness affects shielding effectiveness. We also offer a range of shielding methods for plastic enclosures. A complete absence of interruptions is not a realistic goal since the Faraday cage will have to be opened from time to time so electronics, equipment or people can be moved in or out. Openings are also needed for displays, ventilation, cooling, power supply, signals etc. 3 Shielding works in both directions, items inside the shielded room are shielded from outside influences. (Fig. 3.1)
Technical Library | 2010-04-29 21:40:37.0
The purpose of this paper is to investigate the effects of reflow time, reflow peak temperature, thermal shock and thermal aging on the intermetallic compound (IMC) thickness for Sn3.0Ag0.5Cu (SAC305) soldered joints.
Technical Library | 2010-09-16 18:45:06.0
With PCB complexity and density increasing and also wider use of 3D devices, tougher requirements are now imposed on device inspection both during original manufacture and at their subsequent processing onto printed circuit boards. More complicated and de
