Industry Directory | Manufacturer
Custom High Density Flex Circuit Process Design and Manufacturing In Days, not Weeks.
Industry Directory | Consultant / Service Provider / Manufacturer
CableEye® continuity and HiPot pass/fail & diagnostic Cable & Harness Test Systems w simple scripting, labeling, documentation, cataloging & relay control. Dynamically display continuity, Ω, diodes, IR, dielectric breakdown & more
Connectors is a device that connects two active devices to transmit currents or signals. Domestic connectors, known as the connector and socket, generally refers to electrical connectors. Essential performances of connectors and interconnects can be
New Equipment | Soldering - Other
High specification, bench top rotary table soldering machine A versatile four station rotary bench top soldering machine, ideally suited for high or low volume production, the Quadron combines well proven pumped soldering techniques with advanced PL
Electronics Forum | Tue Jun 08 22:30:05 EDT 2021 | vtdivtecs
So I am having a little trouble with my mydata MY19. its an older machine picked up used and its had its quirks. recently we tried to start adding electrical verification to our workflow, and had to disable it as we were getting intermittent bad pa
Electronics Forum | Tue Jun 13 16:45:30 EDT 2006 | adlsmt
If the only difference is the layer count, check the profile as stated above. If you dont have a profiler you can probably get the local Kic or Mole rep to do a demo on that board. I believe I was the one who stated in an old post that prying the lea
Used SMT Equipment | General Purpose Test & Measurement
The Tektronix TDS5104B oscilloscope is a graph-displaying device - it draws a graph of an electrical signal. In most applications, the graph shows how signals change over time: the vertical (Y) axis represents voltage and the horizontal (X) axis repr
Used SMT Equipment | General Purpose Test & Measurement
Tektronix TDS5104B Bandwidth: 1 Ghz Channels: 4 1 GHz, 5 GS/s, 4 Channel Digital Phosphor Oscilloscope The Tektronix TDS5104B oscilloscope is a graph-displaying device - it draws a graph of an electrical signal. In most applications, the graph s
Industry News | 2015-05-07 19:28:29.0
MIRTEC announce a new strategic cooperation that will empower yield improvement in the electronics manufacturing industry.
Industry News | 2018-04-15 20:01:15.0
SMTA Europe announces Session 4 Technical Program on Electrochemical Reliability at the “Electronics in Harsh Environments Conference” to be held in Amsterdam, Netherlands, on April 25th, 2018.
Technical Library | 2019-06-03 15:32:40.0
ACI Technologies was pleased to assist a customer by conducting elemental analysis on several assemblies displaying severe corrosion. Several board assemblies had failed in the field and exhibited areas of corrosion in close proximity to onboard components. The most common source of corrosion on electronic assemblies is residual flux. Fluxes are specific chemistries applied during the soldering process which improve the wetting of the solder to both the pad and component when forming the solder joint. They can be highly reactive chemicals that, if left on the assemblies, can lead to corrosion, electrical degradation, and decreased reliability. In the presence of moisture and electrical bias, flux residue can enable dendritic growth as a result of electrochemical migration (ECM).
Technical Library | 2020-12-07 15:26:06.0
Temperature cycling testing is a method of accelerated life testing done to PCCs that are exposed to normal operation temperature variations over its lifetime. During the testing, intermittent "open" failures can first occur at the hot and cold extremes of the test, exposing weaknesses in the design and assembly. A poor/weak solder joint fatigues, a via trace or barrel cracks, loose connections or a component fails all causing an intermittent open. When not at extreme temperatures, the PCC assembly relaxes, the "open" closes creating electrical connectivity. If you are monitoring the PCC under test in-situ you will know that an intermittent failure has occurred, and the test could be stopped for inspection. If in-situ monitoring was not implemented, you would not know if there were intermittent failures or not. The PCC gets powered up and works fine at room temperature.
BGA integrated circuits and chip scale packages, CSPs where the solder connections are not visible. This has arisen as a result of the need for greater numbers of interconnections to integrated circuit packages and as a general result of increasing c
Contact Us Sales manager: Mac Xie Mobile: +8618020714662(WhatsApp) Email: at@mooreplc.com Skype: +8618020714662 Contact Us ✭Product Overview✭ SIPART PS2 smart electropneumatic positioner for pneumatic linear and part-turn actuators; 2-,3-
Career Center | Clarksburg, Maryland | Engineering
Immediate opportunities for SMT Solder Specialist. Also have these positions open. All immediate opportunities: Assembler: Must have strong electro mechanical manufacturing skills. Experience with assembly of electro mechanical products in a high
Career Center | San Jose, Nationwide | Engineering,Management
This world-renowned $13B organization is seeking a Product Reliability Engineering Manager (to report directly into the VP) for our San Jose, CA corporate technology office. We prefer candidates in the Silicon Valley area, but will consider candidat
Career Center | , Israel | Engineering,Maintenance,Technical Support
I was born on June , 1972 in Khmelnitsky city , Ukraine . I am male. From 1979 to 1987 I was studying at secondary school #7, having finished which I entered the Technical College of Khmelnitsky in specialty Machine Tools with Computer Numeric Contr
Career Center | banaglore, karnataka India | Maintenance,Production,Quality Control,Technical Support
tel u later
Imagineering, Inc. | https://www.pcbnet.com/blog/controlling-signal-integrity-in-high-speed-pcb-design/
. Signal integrity issues occur when: The shape of a signal changes from the intended state. Electrical noise degrades the signal to noise ratio Undesired noise influences other signals and circuits on a PCB
PCB Libraries, Inc. | https://www.pcblibraries.com/Forum/making-mounting-holes-in-footprint_topic1411.html
. These are part of the body of the connector, not electrical pins. I've had some puzzling problems trying, with Pad Stack Designer, to create these holes. 1
