Technical Library: feeder and calib (Page 1 of 1)

Taking the LED Pick and Place Challenge

Technical Library | 2014-09-25 18:16:47.0

For the past few years there has been a shift in the Lighting Industry that has carried over to the surface mount technology assembly line. What is this shift you may ask? Well it is the LED revolution. This revolution or change in lighting has some very promising results already in practice and many more companies looking to implement the LED technology into their product portfolio's. With a number of companies looking to expand their portfolio to include LED fixtures there has been an increase in the number of companies that have started their own SMT lines, as well as a significant number of contract manufacturers to meet this new industries demands (...)This presentation will discuss some issues in the pick and place process for LEDs and presents a method to troubleshoot and resolve these issues.

Cree, Inc.

0201 and 01005 Adoption in Industry

Technical Library | 2011-02-03 17:58:46.0

First introduced in the year 2000, the 0201 package was sold in significant numbers in the electronics industry by 2003. According to some estimates, it currently accounts for approximately 20% of surface mounted component (SMC) demand worldwide1. This pu

DfR Solutions

SnAgCuBi and SnAgCuBiSb Solder Joint Properties Investigations

Technical Library | 2008-02-05 22:48:55.0

This study investigates the technological properties of quaternary or quinary alloys made by addition Bi or Bi and Sb elements to the SnAgCu solders. The influence of added elements on the electrical and mechanical properties of solder joints created by these solders between PCB and electronic components were evaluated.

Unipress - Institute of High Pressure Physics of the Polish Academy of Sciences

0201 Placement - Only With The Right Team and Tools!

Technical Library | 2003-09-17 02:59:58.0

It appears very logical that the successor of the 0402 size SMD would be the 0201. Curves showing the life-cycle of a body size, from introduction to most used to only for special cases, are very similar for the 1206, 0805, 0603 and 0402. So there is reason to expect that the same will happen with the 0201. Until now there is only little evidence for this, but most technologies come later than expected but faster than expected!

Assembléon

Liquid Tin Corrosion and Lead Free Wave Soldering

Technical Library | 2008-02-12 22:52:41.0

Corrosion of solder pots and solder pot components in wave soldering equipment has been reduced with the introduction of corrosion resistant coatings and improved lead free solder alloys. The latest trends in protecting wave solder machine components from liquid metal corrosion by lead free solder alloys will be presented in order to provide guidelines for evaluating existing equipment as well as for purchasing new systems.

Speedline Technologies, Inc.

Digital manufacturing for traceability: The way to higher product quality and better warranty management

Technical Library | 2010-08-26 21:06:17.0

Driven by high-profile regulations compliance like the TREAD Act, warranty management has become a hot topic across industries worldwide. Recalls are costly and time-consuming events that should be avoided entirely. But without adequate process traceability and product genealogy, too many customers will get defective products and too many products will be recalled for repair or replacement even though they are not defective. Both scenarios have enormous implications for the quality-conscious manufacturer that gets rated on the number of recalls it performs - not to mention the enormous direct costs. The core issue is visibility into product quality.

ASM Assembly Systems GmbH & Co. KG

The Pin-in-Paste (or AART) Process for Odd Form and Through Hole Printed Circuit Boards

Technical Library | 2007-09-27 16:18:15.0

Considerable interest exists in the process known as the pinin- paste, or the Alternative Assembly and Reflow Technology (AART) process. The AART process allows for the simultaneous reflow of both odd-form and through hole devices as well as surface mount components. This process has several advantages over the typical mixed technology process sequence that includes wave soldering and/or hand soldering, often in addition to reflow soldering.

Universal Instruments Corporation

Press Fit Technology Roadmap and Control Parameters for a High Performance Process

Technical Library | 2016-10-27 16:24:23.0

Press-fit technology is a proven and widely used and accepted interconnection method for joining electronics assemblies. Printed Circuit Board Assembly Systems and typical functional subassemblies are connected through press-fit connectors. The Press-Fit Compliant Pin is a proven interconnect termination to reliably provide electrical and mechanical connections from a Printed Circuit Board to an Electrical Connector. Electrical Connectors are then interconnected together providing board to board electrical and mechanical inter-connection. Press-Fit Compliant Pins are housed within Connectors and used on Backplanes, Mid-planes and Daughter Card Printed Circuit Board Assemblies. High reliability OEM (Original Equipment Manufacturer) computer designs continue to use press-fit connections to overcome challenges associated with soldering, rework, thermal cycles, installation and repair. This paper investigates the technical roadmap for press fit technology, putting special attention to main characteristics such, placement and insertion, inspection, repair, pin design trends, challenges and solutions. Critical process control parameters within an assembly manufacturing are highlighted.

Flex (Flextronics International)

  1  

feeder and calib searches for Companies, Equipment, Machines, Suppliers & Information



High Throughput Reflow Oven
Large PCB Dispensing System

Outstanding liquid dispensing and UV curing, all within one platform, watch the video.
Best SMT Reflow Oven

PCB Assembly Supplies - ONLINE STORE


PCBA services - from simple board assembly to complex product development and testing