Manufacturer of advanced process chemistry for plating, masking and stripping. Custom manufacturing of automated equipment for electrodeposion including; hoist systems, reel-to-reel and continuous vertical processing equipment.
Electronics Forum | Fri Sep 08 11:50:39 EDT 2006 | Rob
SN100C is designed not to corrode your pot, and can be used on standard solderpots (after a proper clean out), whereas SACX is still corrosive and if the coating is compromised then could cause problems. Get it in writing from the supplier that the
Industry News | 2008-06-11 18:26:39.0
FINE LINE STENCIL announces Slic Blade™, its newest line of squeegee blades, and a SMT VISION Award winning product.
Industry News | 2013-05-23 22:15:30.0
IDTechEx has recently launched an online browser-based Market Intelligence Portal (www.IDTechEx.com/portal ), bringing you in-depth market intelligence and independent analysis throughout the year.
Supply Sanyo tcm3000 applicator filter cotton (filter): Product Name: filter Brand: Sanyo Model: tcm3000 Place of origin: Taiwan Shape: flakes Features: strong air permeability Package: 100pcs / package SANYO X200/X210 FILTER SANYOT
CNSMT [AA7SA00] GLASS CHIP Glass Flake NXT HBC JIG Material FUJI Mounter Parts CNSMT [AA7SA00] GLASS CHIP Glass Flake NXT HBC JIG Material FUJI Mounter Parts YAMAHA Yamaha mounter YV100XVISION board / vision board / KM5-M441H-02XVISIO YAMAHA Y
Technical Library | 2022-01-19 18:15:45.0
The assay for monitoring the content of sulfite ions (SO32−) is essentially important because sulfite has some seriously toxic effects on both environment and human health. For this, a SO32- electrochemical sensor was fabricated utilizing molybdenum disulfide (MoS2) and Nafion. The cyclic voltammetry (CV) and differential pulse voltammetry (DPV) showed that MoS2 had excellently catalytical activity for the redox of SO32-.
Technical Library | 2020-10-14 14:33:36.0
Epoxy based adhesives are prevalent interface materials for all levels of electronic packaging. One reason for their widespread success is their ability to accept fillers. Fillers allow the adhesive formulator to tailor the electrical and thermal properties of a given epoxy. Silver flake allow the adhesive to be both electrically conductive and thermally conductive. For potting applications, heat sinking, and general encapsulation where high electrical isolation is required, aluminum oxide has been the filler of choice. Today, advanced Boron Nitride filled epoxies challenge alternative thermal interface materials like silicones, greases, tapes, or pads. The paper discusses key attributes for designing and formulating advanced thermally conductive epoxies. Comparisons to other common fillers used in packaging are made. The filler size, shape and distribution, as well as concentration in the resin, will determine the adhesive viscosity and rheology. Correlation's between Thermal Resistance calculations and adhesive viscosity are made. Examples are shown that determination of thermal conductivity values in "bulk" form, do not translate into actual package thermal resistance. Four commercially available thermally conductive adhesives were obtained for the study. Adhesives were screened by shear strength measurements, Thermal Cycling ( -55 °C to 125 °C ) Resistance, and damp heat ( 85 °C / 85 %RH ) resistance. The results indicate that low modulus Boron Nitride filled epoxies are superior in formulation and design. Careful selection of stress relief agents, filler morphology, and concentration levels are critical choices the skilled formulator must make. The advantages and limitations of each are discussed and demonstrated.
Conformal Coating Removal: Micro Abrasive Blasting helps remove conformal coating with precision avoiding any damage to the target circuit boards. This is so useful in semiconductor, electronics and medical industries. It's cost-effective. It's envi
, während Etiketten, Klebstoffe und andere Stoffe abgeschöpft werden. Danach gelangen die Flakes in einen MetaPure®-Reaktor von Krones, wo bei rund 200
. SELF-CLEANING OF COOLING MODULES & COLLECTOR BASE Over time, the inside surface of the cooling module tubes will collect a layer of flux film or crystals (snow flakes