Industry Directory | Manufacturer
Manufacture defluxers, cleaners & maintenance solutions used to remove solder paste, flux residues, SMT Adhesives and other soils during the manufacture of electronic components or during the assembly of printed circuit boards.
Industry Directory | Manufacturer
Nitrogen Cast Lead Free solder Manufacturer, complete range of No Clean and No Residue fluxes Misprint Cleaning Systems completely compressed air driven low cost with no need for electrics 18x12
New Equipment | Rework & Repair Equipment
The new inspection mirror meets clean room requirements yet is sufficiently economical for non-clean room applications. A quality tool for the technician but inexpensive enough to meet the budgetary requirement of modern manufacturing. Economical Br
New Equipment | Cleaning Equipment
Features: 1. A comprehensive cleaning system: the surface of the product residues of organic matter, inorganic substances for thorough and effective cleaning; 2. Automatic cleaning mode: in a clean room to complete the cleaning, rinsing, drying all
Electronics Forum | Tue Dec 26 20:11:47 EST 2006 | davef
What is the make-up of the residue? Is finding this residue new to your standard operation? What has changed?
Electronics Forum | Mon Jan 08 10:29:15 EST 2007 | jaime39
The water soluble flux residue is staying there because the rinsing temperature it may be too low. The flux needs about 130-140 degrees celcius to become soft. If you are using water soluble flux, as per IPC A 610 standards it needs to be remove comp
Used SMT Equipment | Board Cleaners
Aqueous Tech Trident 111 Must sell posted 5/5/15 208V 3 phase 40 Amps Year 2008 Trident III is capable of removing all flux residues including rosin, no-clean and water soluble. Both lead and lead-free flux residues may be removed using the
Used SMT Equipment | Soldering - Reflow
BTU Pyramax 125N Parameters Pyramax Specifications Model Pyramax 125N Atmosphere Air or Nitrogen Conveyor Speed 10-60 in/min 25-152 cm/min Conveyor Width 2-18 in 51-457 mm Heated Length 125 in 3175 mm Heated Zones&
Industry News | 2012-05-11 20:35:45.0
Heller Industries has been awarded a 2012 SMT VISION Award in the category of Soldering Reflow for its 1936 Mark 5 Reflow Oven. The award was presented on April 25, 2012 at the Nepcon China Exhibition.
Industry News | 2003-06-05 08:11:23.0
Kerry co-solvent system pays for itself in 13 months
Parts & Supplies | Pick and Place/Feeders
The definition of SMT SMT is the surface assembly technology,surface mount technology(surface mount technology)(Surface Mounted Technology abbreviation),is currently the most popular electronic assembly industry,a technology and technology. What a
Parts & Supplies | Pick and Place/Feeders
SMT basic process components include: silk screen (or dispensing), placement (curing), reflow soldering, cleaning, testing, repair 1, silk screen: its role is to paste or patch solder paste printed on the PCB pad, the components f
Technical Library | 2020-03-09 10:50:17.0
A customer called the Helpline seeking advice for cleaning no-clean fluxes prior to applying a conformal coating. The customer's assemblies were manufactured with a no-clean rosin based solder paste (ROL0) and were cleaned with an isopropyl alcohol (IPA) wash. After cleaning, a white residue was sometimes found in areas with high paste concentrations and was interfering with the adhesion of the conformal coating (Figure 1). For conformal coatings to adhere properly, the printed circuit board (PCB) surface must be clean of fluxes and other residues. In addition, ionic contamination left by flux residues can lead to corrosion and dendrite growth, two common causes of electronic opens and shorts. Other residues can lead to unwanted impedance and physical interference with moving parts.
Technical Library | 2019-06-03 15:32:40.0
ACI Technologies was pleased to assist a customer by conducting elemental analysis on several assemblies displaying severe corrosion. Several board assemblies had failed in the field and exhibited areas of corrosion in close proximity to onboard components. The most common source of corrosion on electronic assemblies is residual flux. Fluxes are specific chemistries applied during the soldering process which improve the wetting of the solder to both the pad and component when forming the solder joint. They can be highly reactive chemicals that, if left on the assemblies, can lead to corrosion, electrical degradation, and decreased reliability. In the presence of moisture and electrical bias, flux residue can enable dendritic growth as a result of electrochemical migration (ECM).
Flux spray coating on a PCB with uniformal thickness down to 5 microns, with clear edge definition and minimal overspray. Can coat large or shoot dots with the same jet.
Training Courses | | | PCB Rework and Hand Soldering Courses
The PCB rework and hand soldering courses courses cover techniques of rework and repair of PCBs, BGAs and other electronics assemblies, and teach fundamentals of soldering of electronics assemblies.
Training Courses | ONLINE | | PCB Assembly Courses
The PCB assembly courses provide knowledge of different processes and equipment used in TH and SMT assembly of printed circuit boards.
Events Calendar | Tue Apr 14 00:00:00 EDT 2020 - Tue Apr 14 00:00:00 EDT 2020 | ,
Why Are We Cleaning No-Clean?
Events Calendar | Mon May 10 00:00:00 EDT 2021 - Mon May 10 00:00:00 EDT 2021 | ,
Europe Chapter Webinar: Manual Cleaning of Printed Board Assemblies – Step by Step Guide
Article Return to Front Page No-Residue Technolo
SMTnet Express, December 29, 2016, Subscribers: 30,326, Companies: 15,062, Users: 41,660 Partially-Activated Flux Residue Impacts on Electronic Assembly Reliabilities Yanrong Shi, Ph.D., Kyle Loomis, Jennifer Allen, Bruno Tolla, Ph.D.; Kester
| https://www.eptac.com/webinar/flux-classification-part-2-selecting-the-right-flux-for-your-application/
. This Webinar will provide you with a brief insight into: The Purpose of Flux Impact of Flux Residue Selection and Qualification Process Flux Performance Specifications Course Length: 44 Minutes Cost: FREE Presenter(s
| https://pcbasupplies.com/leaded-solder-wire/
levels Clear flux residue offers superior cosmetics No Clean Leaded Flux Cored Solder Wire JM-20 Sn63/Pb40 Specs Product Name Solder Wire JM20 Sn60 Pb40 Product Category Solder Wire Flux content (%) 1.0 - 3.0 Halide content
.gif)
