Electronics Forum: fuji a1038l sensor (Page 1 of 9)

Fuji CP4 feeding sensor problem

Electronics Forum | Wed Sep 12 12:41:53 EDT 2012 | cyber_wolf

You probably have a component that you are telling to advance twice.

Fuji CP4 feeding sensor problem

Electronics Forum | Mon Sep 10 12:18:05 EDT 2012 | benreben

Hi, what's the feeding sensor error? the sensor for cartrige or the sensor on cylinder up of feeder? manual is step mode? if you have the number of error at screen,i have the fuji error code help. in step mode the machine is very slowly,maybe the a

Fuji CP4 feeding sensor problem

Electronics Forum | Sat Sep 08 23:36:14 EDT 2012 | mtech88

Can anyone help me out this Fuji CP4 problem? I just move my machine to a new place, The feeding sensor error keep on poping up. but the mahine work on manual mode. When we switch to auto mode, it just to pick up the part and the machine stop on t

Fuji CP4 feeding sensor problem

Electronics Forum | Wed Sep 12 10:49:46 EDT 2012 | cyber_wolf

Sounds like the feed cylinder sensor. Its a air cylinder hooked to the tape feeder advancing mechanism in the rear of the machine. Go into the I/O and make sure the sensor is changing state when you flag it.

Fuji CP4 feeding sensor problem

Electronics Forum | Wed Sep 12 11:52:31 EDT 2012 | mtech88

Ben: you are right, I think the timing must be off some how. I will check the error code and post it back here. thanks David

Fuji CP4 feeding sensor problem

Electronics Forum | Wed Sep 12 11:55:18 EDT 2012 | mtech88

Sr. Tech: I will check the air cylinder at the rear and see what position when the machine stop. Thanks David

Fuji IP3 clamping problem

Electronics Forum | Wed Mar 13 14:17:03 EST 2002 | dougt

Are these sensors the reflective type? Maybe when the board is unclamped and it goes over the sensor it is seen, and then when it is clamped (raised) it is now out of the range the sensor was set for. That should be easy to adjust. A problem I've

FUJI IP3

Electronics Forum | Sat Dec 12 03:08:55 EST 1998 | USER

My Fuji IP3 keeps getting the Check Sensor Error. What is the problem?

Fuji IP3 clamping problem

Electronics Forum | Fri Mar 08 22:07:31 EST 2002 | winter

I think the reason of the problem is the sensitivity of some sensor.maybe it's the main conveyor arrival sensor .I think you can do a test , make the sensor always on, and tese.

Sigh! - Fuji IP4000 Problem

Electronics Forum | Mon May 10 01:20:07 EDT 2004 | longpham246

Hello! Check your stopper up/down sensor position. This problem has nothing to do with the proper data. Sometimes the sensor position is not correct or sensor contact could cause this problem even I/O mode was OK. Regards! LMQ

  1 2 3 4 5 6 7 8 9 Next

fuji a1038l sensor searches for Companies, Equipment, Machines, Suppliers & Information

ISVI - Industrial Sensor Vision International Corporation
ISVI - Industrial Sensor Vision International Corporation

Industrial Sensor Vision International specializes in advanced camera technology of high resolution fast speed cameras for automation, AOI, 2-D/3-D, SPI inspection and wafer inspection.

Manufacturer

3 Morse Road 2A
Oxford, CT United Arab Emirates

Phone: +1 203 592 8723

thru hole soldering and selective soldering needs

IPC Certification Training from the comfort of your home or office
Dual Lane Reflow Oven

ONLINE IPC Training & Certification
PCB Handling Machine with CE

Best Reflow Oven
PCB Depanelizers

Low-cost, self-paced, online training on electronics manufacturing fundamentals