Electronics Forum | Wed Aug 02 12:27:52 EDT 2017 | action_101
If anyone has any GPD CF9 die sets available for sale, then please contact me. A few specific sets I am looking for are the following: 905-1120C 905-3LA Thanks
Electronics Forum | Fri May 07 13:28:13 EDT 2010 | tonaxel
Hello SR.Tech, yes, the general positions from 1 to 16 are ok. I also changed the pressure of the spring what is on the achsis for the tape transport wheels. This helped a lot for the most wheels but not for all. I will try it again. Maybee the pres
Electronics Forum | Sun Aug 01 21:17:52 EDT 2004 | Eric
I have already been working with GPD regarding this project but at the same time the stage of the project is still on the selection process so I'm still open to other machines to be qualified. As per current machine in house (Micromax II), we have
Electronics Forum | Fri Apr 27 11:23:40 EDT 2007 | pjc
You can get reliable solderpaste dots down to 20-30mil dia. with Type 3. Accurate and repeatable dispensing machine for X-Y-Z placement of the dot is critical. Here are the leading machines: http://www.speedlinetech.com/camalot/index.aspx http://
Electronics Forum | Tue Oct 23 22:12:57 EDT 2007 | davef
1 Tape & reel, automatic * RVSI/Systemation ST-60 * Shinkawa SDP-FA-TAPE 1 * V-TEK TM-5100 * Q Corporation QMT-1500 2 Tape & reel, manual * RVSI/Systemation MT-30 * V-TEK TM-50XL * Q Corporation QMT-1100 3 Tape & reel, peel force tester * RVSI/Syste
Electronics Forum | Thu Jun 04 09:25:21 EDT 1998 | Chrys
| | | Hello: | | | BACKGROUD: SMT components soldered on the top-side of boards that also require wave soldering have the potential to reflow during wave soldering. Reflowing these components during wave soldering is not good. It can cause cold jo
Electronics Forum | Fri Nov 21 12:12:44 EST 2014 | joe98375
On average there are about 3 parts per board that get hand placed (x24 is 72 parts per panel). One of these parts is a big 1W resistor that cannot fit on our axial machine. We also have a Zener Diode that needs to be hand placed because its leads are
Electronics Forum | Fri Jan 13 09:48:27 EST 2017 | westshoredesign
10mins to print an 8mm wheel. Experimenting with both Ninja Flex, and Ninja Semi-Flex, I think the Flex is probably going to be the winner though. Had to upgrade our filament feeder on the printer to use either of them. Totally worth it though. Not s
Electronics Forum | Fri May 24 11:49:55 EDT 2002 | stefwitt
Again, I would like to refer to the tape dimensions and their deviations. In an 8 mm tape the distance from the sprocket holes to the tape pocket is 3.5 mm +/- 0.05 mm. This tolerance is easy to achieve, because in the manufacturing process of the ta
Electronics Forum | Thu Apr 10 17:44:22 EDT 2003 | davef
Q1: Can they be masked so parylene doesn't get underneath? A1: Your parylene applyer may be able to mask area, but in general no. This stuff is cured in a vacuum chamber to make sure that it gets into every past corner. Q2: How do you remove and re
A Manufacturer of High Quality, Precision, Automated Fluid Dispensing and Conformal Coating Systems, SMT Cover Tape Peel Tester and Lead Forming machines for through-hole component preparation.
611 Hollingsworth Street
Grand Junction, CO USA
Phone: (970) 245-0408