Industry Directory | Manufacturer
US manufacturer of metallized ceramic substrates & packages; specializing in PCTF (plated copper over thick film) & low cost AgENIG (silver with electroless nickel and immersion gold plating).
High Tech, Quick Turn, Manufacturer of PCB's up to 44 layer count. Specializing in Prototype and R&D. Mil-Spec 31032 & 55110 Certified. Located in Fremont, CA & Amesbury, MA.
New Equipment | Education/Training
BEST training kits feature REAL circuit boards that represent actual soldering conditions. These training kits feature ".062 thick multilayer boards which are more representative of the thermal conditions of "real" circuit boards. This board feature
New Equipment | Education/Training
This is a "real life" how to solder kit including both throughhole and SMT components. The board has ground planes that you would find in a real PCB assembly. Upon completion the sudents will have a working board. If you are trying to instruct new
Electronics Forum | Tue Sep 23 10:06:29 EDT 2008 | Sean
Hello Vlad, Davef, Your valuable inputs are much appreciated. Many thanks, Sean.
Electronics Forum | Sat Sep 20 07:11:28 EDT 2008 | Sean
Hello All, I used to hear that PCB with immersion silver finishing, its non component location pads, tend to be discolour (Yellowish) after went through heat cycle, such as reflow oven. However, if the component solderbility on the PCB is OK, can w
Industry News | 2003-05-19 10:06:43.0
The PCB is available with a maximum panel size of 406-by-460mm and a minimum board thickness of 0.8mm.
Industry News | 2003-02-07 09:13:12.0
The Sessions Covered Current and Emerging Technologies
Parts & Supplies | Circuit Board Assembly Products
1). 1+C+1 HDI, buried/blind L1-L5/L5-L8 vias. 2). FR-4 Material, 1 oz weight. 3). 8 layer, 1.6mm thick. 4). 4/4 mils track and space 5). Min.drill 0.1mm 6). Green solder mask/ white silkscreen 7). Immersion gold over nickel
Parts & Supplies | General Purpose Equipment
The conductive elastomer have good conductive,and the products are mainly used in army electronic equipments like spaceflight,aviation,ect. We can produce this products according the drawing supplied by our customers. The materials: Silicon with Si
Technical Library | 2019-06-07 14:49:54.0
ACI Technologies was contacted in regards to poor solder joint reliability. The customer submitted an assembly that was exhibiting intermittent opens at multiple locations on a ball grid array (BGA) component. The assembly’s functionality did not survive international shipping, essentially shock and vibration failures, immediately making the quality of the solder joints suspect. The customer was asked about the contract manufacturer and the reflow oven profile as well as the solder paste and surface finish used. The ACI engineering staff evaluated the contract manufacturer’s technique and determined that they were competent in the methods they used for placing thermocouples in the proper locations and developing the reflow oven profile. The surface finish was unusual, but not unheard of, in that it was hard gold over hard nickel, rather than electroless nickel immersion gold (ENIG). The customer was able to supply boundary scan testing data which showed a diagonal row of troublesome BGA pins.
Technical Library | 2015-11-25 14:15:12.0
In this study various printed circuit board surface finishes were evaluated, including: organic solderability preservative (OSP), plasma finish (PF), immersion silver (IAg), electroless nickel / immersion silver (ENIS), electroless nickel / immersion gold hi-phosphorus (ENIG Hi-P), and electroless nickel / electroless palladium / immersion gold (ENEPIG). To verify the performance of PF as a post-treatment option, it was added to IAg, ENIG Hi-P, and ENEPIG to compare with non-treated. A total of nine groups of PCB were evaluated. Each group contains 30 boards, with the exception on ENIS where only 8 boards were available.
This is what the fully assembled How to Solder Kit looks like. Depress the button and one of the LEDs will remain lit at the end (it eventually times out). You can add some kind of template so each LED position has some meaning. The PCB has a real gr
Events Calendar | Wed Apr 20 00:00:00 EDT 2022 - Wed Apr 20 00:00:00 EDT 2022 | ,
Virtual Course: Selection Criteria of Surface Finish for Next Generation PCB Technologies
Career Center | Phoenix, Arizona | Engineering,Management,Production,Quality Control,Research and Development,Sales/Marketing,Technical Support
• Highly motivated, solution oriented professional with proven record synergizing scientific, engineering, and business administration backgrounds to drive and sustain customer satisfaction and long term improvements. • Articulate communicator that a
Imagineering, Inc. | https://www.pcbnet.com/capabilities/assembly/technology-roadmap/
• Inner Layer - 10 oz • Inner Layer - 16 oz Buried/Blind Via 10+N+10 (HDI) Plasma Desmear Yes Outline Tolerance +/-.004 Surface Finish • HASL • ENIG • Immersion Silver • OSP (ENTEK) • Carbon • Immersion Tin • Electrolyic Gold • ENEPIG • ENIPIG Impeadance Control
PCB Libraries, Inc. | https://www.pcblibraries.com/forum/ipc-standards-for-manufacturing-assembly_topic877_post9030.html
and Flexible Adhesive Bonding Films IPC-4204 - Flexible Metal-Clad Dielectrics for Use in Fabrication of Flexible Printed Circuitry IPC-4552 - Specification for Eletroless Nickel/Immersion Gold (ENIG