Electronics Forum | Tue Jul 14 18:42:41 EDT 2009 | anndi
1smtdude, I interested in your explaination of > re-work an underfill part. You mention the > material can be heated to a plastic state to > become vicious... do you know usually what range > is the temperate? (guess it can depend on the > type
Electronics Forum | Wed Jan 17 15:13:24 EST 2007 | jaime39
When placing the part to be reflow try applying heat to the board from the secondary side until the primary side has a temperature of about 130 degrees celcius. Following this procedure it should minimize the heat exposure of the part being soldered.
Industry News | 2003-08-27 10:43:02.0
This 41-page document is the complete source for printed circuit board and electronics assembly standards and publications for design, materials, manufacturing, assembly, quality and test.
Industry News | 2003-08-27 10:58:00.0
Lead free solders and embedded passives headline professional development schedule at the 2003 IPC Annual Meeting
Technical Library | 2022-10-31 17:25:37.0
Mixed formulation solder alloys refer to specific combinations of Sn-37Pb and SAC305 (96.5Sn–3.0Ag–0.5Cu). They present a solution for the interim period before Pb-free electronic assemblies are universally accepted. In this work, the surfaces of mixed formulation solder alloys have been studied by in situ and real-time Auger electron spectroscopy as a function of temperature as the alloys are raised above the melting point. With increasing temperature, there is a growing fraction of low-level, bulk contaminants that segregate to the alloy surfaces. In particular, the amount of surface C is nearly _50–60 at. % C at the melting point. The segregating impurities inhibit solderability by providing a blocking layer to reaction between the alloy and substrate. A similar phenomenon has been observed over a wide range of (SAC and non-SAC) alloys synthesized by a variety of techniques. That solder alloy surfaces at melting have a radically different composition from the bulk uncovers a key variable that helps to explain the wide variability in contact angles reported in previous studies of wetting and adhesion. VC 2011 American Vacuum Society. [DOI: 10.1116/1.3584821]
Technical Library | 2007-11-01 17:16:07.0
This paper discusses micro-filled epoxy-based conducting adhesives modified with nanoparticles, conducting polymers, and low melting point (LMP) fillers for z-axis interconnections, especially as they relate to package level fabrication, integration,
Lyra Reflow Oven is a soft soldering that realizes the mechanical and electrical connection between the solder ends of surface mount components or the pins and the printed board pads by remelting the solder paste pre-distributed on the printed board
Events Calendar | Thu Oct 21 00:00:00 EDT 2021 - Thu Oct 21 00:00:00 EDT 2021 | ,
Great Lakes Chapter Webinar: Low Melting Alloy & Selection of the Right Chemistry for Reliability
SMTnet Express, July 1, 2015, Subscribers: 22,969, Members: Companies: 14,445, Users: 38,464 Reliability Screening of Lower Melting Point Pb-Free Alloys Containing Bi Joseph M. Juarez, Michael Robinson, Joel Heebink; Honeywell International
Influence of Nanoparticles, Low Melting Point (LMP) Fillers, and Conducting Polymers on Electrical, Mechanical, and Reliability Performance of Micro-Filled Conducting Adhesives for Z-Axis Interconnections. Influence of Nanoparticles, Low Melting
| http://etasmt.com/cc?ID=te_news_bulletin,21161&url=_print
. In the reflow section, the peak soldering temperature varies depending on the solder paste used. Generally, the melting point temperature of the solder paste plus 20-40°C is recommended
| https://www.eptac.com/blog/in-search-of-the-ultimate-instructor?hsLang=en
. Read More Why Get IPC Certified Leaded vs. Lead-Free Solder: Which is Better? Leaded solder has been the preferred material for electronic manufacturing for decades due to its low cost, lower melting point, and ease of use
