Electronics Forum: mpm and up2000b (Page 1 of 9)

MPM UP2000 alarm "hardware limit warning"

Electronics Forum | Fri Sep 24 06:17:47 EDT 2010 | bullyparade

Hi all, we use a MPM UP2000/B printer and facing the following problem: During startup/initialisation process the printer stops after a while and comes up with the following alarm "hardware limit warning". This can be repeated several times with the

SMTECH pro's and con's

Electronics Forum | Fri Oct 05 08:35:29 EDT 2001 | PeteC

I believe this machine is now the MPM UP 100 and is supported thru Speedline Technologies-MPM and is now mfg.'d in Franklin Mass.

MPM Up2000 and SMEMA

Electronics Forum | Mon Sep 12 09:26:00 EDT 2016 | awhite

Our MPM Up2000 HIE is having a communication problem with any upstream machine we place in front of it...i.e. conveyor, board loader, etc. It all started when we removed a conveyor from inbetween it and a board loader, and hooked those machines up di

MPM Up2000 and SMEMA

Electronics Forum | Tue Sep 13 02:31:50 EDT 2016 | bukas

board input sensor sensitivity? maybe conveyor movement triggers it and because of that it sends pulse. conveyor moves few millimeters, how does machine act?

MPM Up2000 and SMEMA

Electronics Forum | Tue Sep 13 07:32:51 EDT 2016 | bukas

that sounds like bad relay or relay control. are you in position to check it on relay pins? I would go from there.

MPM Up2000 and SMEMA

Electronics Forum | Wed Sep 14 23:30:30 EDT 2016 | ariss_t

Hi, my 2cent.. u could try to check the sensibility of the camera board stop sensor.. maybe it detect something i.e support block.. do reply when u found the actual root cause.. thanks..

High-end SPI and AOI?

Electronics Forum | Tue Oct 13 08:09:53 EDT 2009 | kudamarani08

Can anyone help me recommend or simulate a SPI and AOI machine that can balance our FUJI NXT 1 with 14 modules. We are using MPM accela printer. 200 UPH is our target. Here's the PCB dimension length(x) = 399.92mm width(y) = 141.626mm Thanks all!

MPM Up2000 and SMEMA

Electronics Forum | Wed Sep 14 02:41:49 EDT 2016 | bukas

here is well explained SMEMA interface http://www.daghee.com/?p=326 so, disconnect printer from upline modules and check are any 2 of 4 pins shortened(should be pins No 1 & 2) while machine is ready state. when machine is in busy state the same pin

MPM Up2000 and SMEMA

Electronics Forum | Thu Sep 15 06:45:26 EDT 2016 | awhite

Hi Ariss_T, Thanks! I actually did check that...that was one of my first thoughts as well. While in the I/O, I slide a raw board back and forth under the camera/sensor and it acted appropriately. I will definitely update this thread as new informa

High-end SPI and AOI?

Electronics Forum | Tue Oct 13 22:56:22 EDT 2009 | cpcompany

Can anyone help me recommend or simulate a SPI > and AOI machine that can balance our FUJI NXT 1 > with 14 modules. We are using MPM accela printer. > 200 UPH is our target. > > Here's the PCB > dimension > > length(x) = 399.92mm width(y) = >

  1 2 3 4 5 6 7 8 9 Next

mpm and up2000b searches for Companies, Equipment, Machines, Suppliers & Information

SMT feeders

Easily dispense fine pitch components with ±25µm positioning accuracy.
Sell Used SMT & Test Equipment

Software programs for SMT placement and AOI Inspection machines from CAD or Gerber.
RETROFIT for More Effective Dispensing

Benchtop Fluid Dispenser
2021 IPC Training Schedule

World's Best Reflow Oven Customizable for Unique Applications