Industry Directory: ohm (7)

OHM LOADS INC

Industry Directory |

Custom AC/DC Resistive Load Bank solutions built in a timely and cost effective manner to our customer's exact specifications from 25W to 30KW in a single chassis. Three of our 30KW chassis can be integrated to create a 90KW load.

TechNote Time Watch Company

Industry Directory | Other

Ohm's law wristwatches, desk clocks and wall clocks for DC or AC applications, with unique resistor band color chart. Handy for any electronics professional, student or hobbyist.

New SMT Equipment: ohm (1668)

M8 Threaded stainless steel NTC thermistor temperature sensor 10K ohm

M8 Threaded stainless steel NTC thermistor temperature sensor 10K ohm

New Equipment | Cable & Wire Harness Equipment

Threaded stainless steel tube NTC thermistor temperature sensor probe for temperature measurement of liquid, water, air, etc. Ideal for vessel and pipe installation. Typical application coffee maker, tea kettle, water heater boilers, soybean milk coo

Amwei Thermistor Sensor

woodward 1785-655 100 ohm rtd to 0-5 volt converter

woodward 1785-655 100 ohm rtd to 0-5 volt converter

New Equipment | Components

woodward 1785-655 100 ohm rtd to 0-5 volt converter  Pls kindly know that the advantage we have 1.Origin goods 2.In stock 3.One-year warranty 4.Timely delivery 5.The best price 6.All the goods will be tested before shipment. If there is a

Huge Technology Automation Co., Ltd

Electronics Forum: ohm (158)

marking standard for .1% resistors?

Electronics Forum | Mon Sep 18 14:43:06 EDT 2006 | jdengler

Steve, I don't think it was a Yageo if the value is 10 ohms. Yageo would label them as 10R0 for 10 ohms. 1002 would be a 10K ohm resistor. Jerry

Quad IVc Main Breaker

Electronics Forum | Tue May 07 15:30:41 EDT 2013 | bobpan

your card is probably bad.....you can ohm out the motor and cable if you want... z motor windings 1.36 ohms z motor cable and windings 1.82 ohms good luck

Used SMT Equipment: ohm (278)

Tektronix DTGM30

Tektronix DTGM30

Used SMT Equipment | General Purpose Test & Measurement

Specifications: Number of Channels - 2 AMPLITUDE RANGE - MAX 1.25Vp-p into 50ohm AMPLITUDE RANGE - MIN .03Vp-p into 50ohm STANDARD MEMORY/RECORD LENGTH

Test Equipment Connection

Agilent 8714ES

Agilent 8714ES

Used SMT Equipment | In-Circuit Testers

Agilent 8714ES RF Network Analyzer (S-parameter), 300 kHz to 3 GHz The Agilent 8714ES features an S-parameter test set with full two-port vector-error correction, providing complete and accurate measurements of device S-parameters. Two independ

Test Equipment Connection

Industry News: ohm (104)

More Capacity for Compact Electrolytics

Industry News | 2003-03-20 08:12:57.0

Nichicon has increased the top capacitance value of its WG series of surface mount electrolytic capacitors from 1000 to 1500uF.

SMTnet

Ease of Application for Infiniband I/O Connectors

Industry News | 2003-04-22 09:33:13.0

Honda Connectors has released its first Infiniband I/O connectors, designed for easy assembly in high-speed differential signal applications.

SMTnet

Parts & Supplies: ohm (90)

Technical Library: ohm (1)

3D Printing Electronic Components And Circuits With Conductive Thermoplastic Filament

Technical Library | 2023-06-02 14:13:02.0

This work examines the use of dual-material fused filament fabrication for 3D printing electronic componentsand circuits with conductive thermoplastic filaments. The resistivity of traces printed fromconductive thermoplastic filaments made with carbon-black, graphene, and copper as conductive fillerswas found to be 12, 0.78, and 0.014 ohm cm, respectively, enabling the creation of resistors with valuesspanning 3 orders of magnitude. The carbon black and graphene filaments were brittle and fracturedeasily, but the copper-based filament could be bent at least 500 times with little change in its resistance.Impedance measurements made on the thermoplastic filaments demonstrate that the copper-based filamenthad an impedance similar to a copper PCB trace at frequencies greater than 1 MHz. Dual material3D printing was used to fabricate a variety of inductors and capacitors with properties that could bepredictably tuned by modifying either the geometry of the components, or the materials used to fabricatethe components. These resistors, capacitors, and inductors were combined to create a fully 3Dprinted high-pass filter with properties comparable to its conventional counterparts. The relatively lowimpedance of the copper-based filament enabled its use for 3D printing of a receiver coil for wirelesspower transfer. We also demonstrate the ability to embed and connect surface mounted components in3D printed objects with a low-cost ($1000 in parts), open source dual-material 3D printer. This work thusdemonstrates the potential for FFF 3D printing to create complex, three-dimensional circuits composedof either embedded or fully-printed electronic components.

A.T.E. Solutions, Inc.

Videos: ohm (31)

Siemens PL EA 03012564-03

Videos

03027548-01 Guide, left-hand side 03027563-01 Loctite 7063 CLEANER 03027570-03 HOTLINK CARD CPCI A14 K-01 03027644-01 HOLDER FOR CABLE INTERFACE 03027646-02 JUMPER 120 Ohm SUD-D PIN 03027905-01 Adapter cable MTC2 CAN bus 03028249-02 Pneumatic S

Qinyi Electronics Co.,Ltd

Brand new and original

Brand new and original

Videos

Contact Us Sales manager: Mac Xie Mobile: +8618020714662(WhatsApp) Email: at@mooreplc.com Skype: +8618020714662 Contact Us   ✭Product  Overview✭ Brand GE Fanuc Series VersaMax Manufacturer GE Intelligent Platforms (Former); Emerson Automati

MOORE Automation Ltd.

Career Center - Resumes: ohm (2)

Sr. Process & Quality Engineer

Career Center | Houston, Texas USA | Engineering,Management,Quality Control,Technical Support

Seasoned Process & Quality Engineer. Degreed Chemical Engineer. 20+ years in Electronics Semiconductor manufacturing. Proficient in Quality Statistical tools, Design of Experiments, FMEAs, APQP, PPAP, ISO 9000, ISO/TS 16949 etc.

Field Service Engineer / Manufacturing Engineer

Career Center | Colton, California USA | Engineering,Maintenance,Production,Quality Control,Research and Development,Technical Support

• Strong experience with the installation, training, and repair on a variety of electro-mechanical, pneumatic, PLC, or computer controlled systems. • Strong Knowledge in SMT equipment, Screen Printer, AOI/SPI, Conformal Coat Systems, Reflow oven, X-R

Express Newsletter: ohm (11)

Partner Websites: ohm (185)


ohm searches for Companies, Equipment, Machines, Suppliers & Information

Sm t t t t t t t t t t net
  1 2 3 4 5 6 7 8 9 10 Next