Industry Directory | Manufacturer
One-Stop Solution for PCB & Prototype Assembly Expanded PCB manufacturing capabilities to support advanced designs with demanding requirements including laser-drilled microvias, cavity boards, heavy copper up to 20 oz., via-in-pad
Industry Directory | Manufacturer
We specialize in Flex PCBs, Ridgid Flex, Long Flex PCBs and RF (radio frequency) Boards. Our engineering team has seen it all.
The DV-03 is a air-actuated balanced spool valve for consistent dispensing of high viscosity fluids. For precision, you can control the amount of fluid dispensed by adjusting the fluid pressure, pulse time, and selecting the appropriate dispense tip
PCB depaneling often happen right after SMT processing or after soldering,or after in-circuit test in the assembly line.PCB depaneling machine to be a important equipment in high-volume electronics assembly production. To choose the ASCEN PCB de
Electronics Forum | Thu Dec 07 00:55:51 EST 2006 | billylim
As you are aware the common method to rework BGA is : 1. Remove BGA with hot air reflow machine ( SRT as current practice) 2. Clean the BGA pad using solder iron and solder wick. 3. Replace BGA with SRT rework machine. The problem we have with
Electronics Forum | Thu Dec 07 20:28:07 EST 2006 | davef
When rushing to get a job done, it's easy to accidently remove solder mask from a nearby via when dressing BGA pads after removing the part. Just hit the via with some super glue [then say a small prayer] and push on. As an alternative, look here:
Used SMT Equipment | In-Circuit Testers
Rohde & Schwarz CMW500 loaded with options Wideband Radio Communication Tester Rohde & Schwarz CMW500 LTE FDD CDMA2000 1XEV-DO with the following configuration: CMW500 Hardware Options Included: H051F/H052F/H054B/H055H/H090A/H100A/H110A/H200
Used SMT Equipment | In-Circuit Testers
Rohde & Schwarz CMW500 loaded with options Wideband Radio Communication Tester Rohde & Schwarz CMW500 LTE FDD CDMA2000 1XEV-DO with the following configuration: CMW500 Hardware Options Included: H051F/H052F/H054B/H055H/H090A/H100A/H110A/H200
Industry News | 2011-11-20 13:36:13.0
GPD Global has been awarded two Global Technology Awards in the categories of Adhesives/Coatings/Encapsulants and Dispensing Equipment for its PCD Dispensing on the MAX Series Platform
Industry News | 2003-04-18 08:31:57.0
Unichem to enhance its support and service for North American dry film photoresist and soldermask lamination equipment customers.
Parts & Supplies | Pick and Place/Feeders
USB-Keyboard Active Key with Touch-Pad
Parts & Supplies | Pick and Place/Feeders
PS2-Keyboard Active Key with Touch-Pad
Technical Library | 2019-05-29 01:47:22.0
1.Vias near SMD pads: Solder can flow into the via after melted. As a result cold joint will appear in the end. Check the picture below. 2.Vias on SMD pads: Solder can flow into the via more easier after melted. Check the picture below. 3.Via opening without soldermask covered. When workers solder TH parts by hand, soldering iron can touch vias sometime, then tiny amounts molten solder will stay on vias. This can lead to electrical short easily. We recommend you make all vias tenting (covered by solder mask) if it is possible.
PCBNPI-Professional PCB Fab/PCB Assembly Service Provider From China
Technical Library | 2019-10-10 00:26:28.0
Voids are a plague to our electronics and must be eliminated! Over the last few years we have studied voiding in solder joints and published three technical papers on methods to "Fill the Void." This paper is part four of this series. The focus of this work is to mitigate voids for via in pad circuit board designs. Via holes in Quad Flat No-Lead (QFN) thermal pads create voiding issues. Gasses can come out of via holes and rise into the solder joint creating voids. Solder can also flow down into the via holes creating gaps in the solder joint. One method of preventing this is via plugging. Via holes can be plugged, capped, or left open. These via plugging options were compared and contrasted to each other with respect to voiding. Another method of minimizing voiding is through solder paste stencil design. Solder paste can be printed around the via holes with gas escape routes. This prevents gasses from via holes from being trapped in the solder joint. Several stencil designs were tested and voiding performance compared and contrasted. In many cases voiding will be reduced only if a combination of mitigation strategies are used. Recommendations for combinations of via hole plugging and stencil design are given. The aim of this paper is to help the reader to "Fill the Void."
The PCB Footprint Expert is a powerful CAD library development tool powered by our own proprietary CAD LEAP Technology (Libraries Enhanced with Automated Preferences). It is packed with very powerful advanced library management features that cuts foo
To see more visit Pillarhouse here: https://www.pillarhouse.co.uk/products/selective-soldering-handload/pilot-handload Economical, compact, single point selective soldering system The all-new ultra-low-cost Pilot machine has been designed as an ent
Training Courses | | | PCB Assembly Courses
The PCB assembly courses provide knowledge of different processes and equipment used in TH and SMT assembly of printed circuit boards.
Events Calendar | Mon Apr 23 00:00:00 EDT 2018 - Thu Apr 26 00:00:00 EDT 2018 | Shanghai, China
SMTA China East Conference 2018
Events Calendar | Thu Oct 03 00:00:00 EDT 2019 - Thu Oct 03 00:00:00 EDT 2019 | ,
IPC Tech Ed Webinar Series: Ball Grid Array (BGA) and Bottom Termination Component (BTC) Design and Assembly Challenges: Reflow Profiling to Achieve Low Defect Rates and Successful Assembly! – Part 2
Career Center | , | Engineering,Sales/Marketing,Technical Support
Applications Engineer with over 20 years of combined Manufacturing/Field Service/Applications Engineering experience in the SMT industry.
SMTnet Express, July 16, 2020, Subscribers: 28,512, Companies: 11,045, Users: 25,964 Via In Pad - Conductive Fill or Non-Conductive Fill? Credits: Advanced Circuits In the early 2000s the first fine-pitch ball grid array devices became popular
| https://pcbasupplies.com/pads-and-accessories/
Pads and Accessories Login Create Account Contact View My Cart Menu × Categories Hand Soldering & Rework Automation Tooling PCB Support Systems Soldering Robots Material Handling Dry Storage Cabinets Component Handling Selective Solder Nozzles Pick
| https://www.eptac.com/ask/soldering-wires-to-pads-with-a-lap-joint/
Soldering Wires to Pads With a Lap Joint - EPTAC - Train. Work Smarter. Succeed Looking for solder training standards, manuals, kits, and more