Technical Library | 2017-05-31 18:19:44.0
These guidelines give the assembly team a standardized, no-nonsense method to produce a reliable panelization solution. By eliminating panelization guesswork, you ensure successful assembly even for complex projects.
Technical Library | 2018-02-14 22:58:54.0
This document describes general guidelines and attention points for PCB design regarding selective soldering. The guidelines can be applied for Select Wave and/or Multi Wave soldering process in both leaded and leadfree alloy. When a PCB is designed according to these guidelines, a stable and solid solder-process can be guaranteed.
Technical Library | 2023-10-23 18:28:42.0
This application note discusses the Maxim Integrated's wafer-level packaging (WLP) and provides the PCB design and surface-mount technology (SMT) guidelines for the WLP
Technical Library | 2023-10-09 15:18:50.0
This technical document provides necessary information and general guidelines for soldering and PCB design for the Würth Elektronik eiSos MEMS sensor products with an LGA surface-mount package
Technical Library | 2009-03-25 17:14:11.0
This article presents design guidelines for helping users of HDMI mux-repeaters to maximize the device's full performance through careful printed circuit board (PCB) design. We'll explain important concepts of some main aspects of high-speed PCB design with recommendations. This discussion will cover layer stack, differential traces, controlled impedance transmission lines, discontinuities, routing guidelines, reference planes, vias and decoupling capacitors.
Technical Library | 2013-03-27 23:43:40.0
Vapor phase, once cast to the annals’ of history is making a comeback. Why? Reflow technology is well developed and has served the industry for many years, it is simple and it is consistent. All points are true – when dealing with the centre section of the bell curve. Today’s PCB manufacturers are faced with many designs which no longer fall into that polite category but rather test the process engineering groups with heavier and larger panels, large ground planes located in tricky places, component mass densities which are poorly distributed, ever changing Pb Free alloys and higher process temperatures. All the time the costs for the panels increase, availability of “process trial” boards diminishes and yields are expected to be extremely high with zero scrap rates. The final process in the assembly line has the capacity to secure all the value of the assembly or destroy it. If a panel is poorly soldered due to poor Oven setup or incorrect programming of the profile the recovery of the panel is at best expensive, at worst a loss. For these challenges people are turning to Vapor Phase.
Technical Library | 2010-08-19 17:50:32.0
This article looks at each of the roles of the engineer and PCB designer, considers the traditional design process, and makes suggestions on how the designer can contribute significantly to improving a design’s overall signal integrity while simultaneousl
Technical Library | 2024-02-05 17:51:01.0
Objective: Drying = reducing the humidity in PCB before soldering Preventing delamination caused by thermal stress after moisture absorption Methods: Drying in convection and/ or vacuum oven Parameters subject to material type, soldering surface, layer count, time to soldering, layout (copper-plated areas)
Technical Library | 2023-10-09 16:10:02.0
This document provides high-level PCB design, sensor mounting, and handling guidelines for TDK IMU devices, which incorporate a combination of gyroscopes and accelerometers. Each sensor has specific requirements to ensure the highest performance in a finished product. For a layout assessment of your design, including placement and estimated temperature disturbances, please contact TDK. The TDK IMU devices discussed in this document (ICM-40607x, ICM-40608, ICM-42xxx, ICM-43xxx, and ICM-45xxx products) consist of 3-axis MEMS gyroscopes and 3-axis MEMS accelerometers.
Technical Library | 2017-11-30 10:29:29.0
Each year the electronics industry is faced with new product designs that call for smaller printed circuit boards (PCBs) to function in more aggressive and rigorous service environments. As demands change, conformal coating is becoming increasingly adopted to ensure PCB reliability in environments where moisture, condensation, dust, dirt, salts, chemicals, abrasion, thermal shock, mechanical shock, and other factors can all affect circuit performance. This guide reviews the benefits of using light-cure conformal coatings as well as cost justification, typical processing guidelines and best practices, product selection criteria, data, and industry specifications.
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
1750 Mitchell Ave.
Oroville, CA USA
Phone: (888) 406-2830
