Automatic solder paste printer machine for 1200mm PCB Description: LK-F1200 Ideal for LED production which for Accuracy it has built-in ±10 micron alignment,and ±25 micron wet print repeatability (≧2.0Cpk@6sigma) with 20 seconds total throughpu
New Equipment | Cleaning Agents
CYBERSOLV® C8508 is the latest generation spray cleaner for reflow ovens and general equipment maintenance cleaning. CYBERSOLV® C8508 has been tested on the toughest baked on flux residues with great success and has proven effective on the latest lea
Electronics Forum | Mon Nov 25 12:32:20 EST 2002 | davef
Now that is a BIG step. Stencil type: * A metal squeegee is fine with stepped stencils. * A rubber squeegee is fine with stepped stencils. Comments on step stencil "keepouts" are: * Use an ample space around the stepped down component pads that is
Electronics Forum | Thu Jan 02 15:32:26 EST 2003 | Mark
Hello. Sometimes metal squeegees DO work with stepped stencils. You will always get much better results with metal squeegees compared to polymer blades. The only requirement for the metal squeegee to work, you need about 0.06 in clearance for eve
Industry News | 2024-04-16 12:07:28.0
In the competitive realm of manufacturing solutions, comprehensive after-sales services often determine industry leaders. I.C.T, as a SMT solution provider, exemplifies this ethos through its recent collaboration with a burgeoning smart electric meter factory in Uruguay.
Industry News | 2024-03-27 09:07:10.0
The world of PCB assembly is constantly evolving, and Red Glue SMT Solutions offer a revolutionary approach for double-sided printed circuit board assemblies (PCBAs). This innovative technique overcomes limitations of traditional solder paste and reflow ovens, paving the way for increased efficiency and cost savings.
Technical Library | 2015-08-25 13:51:27.0
The stencil printing process is one of the most critical processes in the electronic production. Due to the requirement: "faster and smaller" it is necessary to place components with different paste volume close together without regard to solder paste printing. In our days it is no longer possible to control the solder paste volume only by adjustment of the aperture dimensions. The requirements of solder paste volumes for specific components are realized by different thicknesses of metal sheets in one stencil with so called step stencils. The step-down stencil is required when it is desirable to print fine-pitch devices using a thinner stencil foil, but print other devices using a thicker stencil foil. The paper presents the innovative technology of step-up and step-down stencils in a laser cutting and laser welding process. The step-up/step-down stencil is a special development for the adjustment of solder paste quantity, fulfilling the needs of placement and soldering. This includes the laser cutting and laser welding process as well as the resulting stencil characteristics and the potential of the printing process.
Technical Library | 2023-07-25 16:25:56.0
This paper address two significant applications of stencils in advance packaging field: 1. Ultra-Thin stencils for miniature component (0201m) assembly; 2. Deep Cavity stencils for embedded (open cavity) packaging. As the world of electronics continues to evolve with focus on smaller, lighter, faster, and feature-enhanced high- performing electronic products, so are the requirement for complex stencils to assemble such components. These stencil thicknesses start from less than 25um with apertures as small as 60um (or less). Step stencils are used when varying stencil thicknesses are required to print into cavities or on elevated surfaces or to provide relief for certain features on a board. In the early days of SMT assembly, step stencils were used to reduce the stencil thickness for 25 mil pitch leaded device apertures. Thick metal stencils that have both relief-etch pockets and reservoir step pockets are very useful for paste reservoir printing. Electroform Step-Up Stencils for ceramic BGA's and RF Shields are a good solution to achieve additional solder paste height on the pads of these components as well as providing exceptional paste transfer for smaller components like uBGAs and 0201s. As the components are getting smaller, for example 0201m, or as the available real estate for component placement on a board is getting smaller – finer is the aperture size and the pitch on the stencils. Aggressive distances from step wall to aperture are also required. Ultra-thin stencils with thicknesses in the order of 15um-40um with steps of 15um are used to obtain desired print volumes. Stencils with thickness to this order can be potential tools even to print for RDLs in the package.
https://www.ascen.ltd/Products/PCB_board_assembly_system/vision_measurin/507.html Vision Measuring Machine and image measuring instrument can be used for dimensional accuracy measurement of various molds, aircraft, automobile, mobile phone, computer,
SMT Express, Volume 2, Issue No. 3 - from SMTnet.com Volume 2, Issue No. 3 Thursday, March 16, 2000 Featured Article Return to Front Page Stencil Design for Mixed Technology Through-hole / SMT Placement and Reflow by William E. Coleman, Photo
| https://pcbasupplies.com/ekra/
: $277.10 Add to Cart Compare Quick view EasyBraid | sku: EB41E2424 STENCIL ROLL, EKRA 23.50 IN x 23.50 IN, 0.55 IN CORE ID, 33 FT LONG, 16/CASE Under Stencil Rolls for Ekra Printers Used in SMT
| https://www.smtfactory.com/a-beneficial-step-to-deepen-global-cooperation.html
& Maintenance Sitemap Product List SMT Production Lines Reflow Oven SMT Stencil Printer Pick And Place Machine Wave Soldering Machine PCB Handling Machine Video View More Get inspired Subscribe for our
