PCB Router Function: Used for routed PCB panel singulation with lower stress. PCB Router Advantages: Lower mechanical stress Precise tooling High quality of cuts Less dust PCB Router Specification: Model Number SMTR17
Pcb board separator v cut pcb aluminium separator features: 1.Decrease the stress , invoide the welding pot break. 2.Adjust the up guide slip by manual, which can solve the V cut depth different problem. 3. There is the guide for V groove, whi
Electronics Forum | Thu Sep 03 09:57:27 EDT 1998 | Gary Simbulan
| Has anyone been able to link a Mydata with the Pads Software. The book say's it can not be done but someone told you can?????? Could someone put me on the right road. | Thank You | John Kirby John, Check out UNICAM at www.unicam.com. I use UNICAM
Electronics Forum | Wed Sep 09 17:22:41 EDT 1998 | Phil Teerink
| | | Has anyone been able to link a Mydata with the Pads Software. The book say's it can not be done but someone told you can?????? Could someone put me on the right road. | | Thank You | | John Kirby | John, | Check out UNICAM at www.unicam.com.
Modern high performance Manncorp / Autotronik pick and place machine with 60 electronic smart feeders. The current model is the MA392v1 or BA392v1 and both have a base price of around 70,000.00. It is my understanding that this machine has all the sa
better pics: Hires pics and a movie Ok, I have a Siemens ms72A pick and place machine for sale. This is a 1990's vintage machine. This machine was originally controlled by the hp-9000 computer it came with over IEEE488 GPIB bus. Lucky for me
Industry News | 2013-08-15 20:58:22.0
Heller Industries announced today that they have entered into a joint development agreement with International Business Machines Corporation (NYSE: IBM), to collaborate on the development of fluxless mass reflow furnace equipment and process for high volume manufacturing. The fluxless process utilizes gas phase formic acid to replace standard fluxing agents, and eliminates the need for pre-reflow fluxing and post-reflow flux cleanup steps.
Industry News | 2016-11-07 16:28:47.0
GPD Global expands the performance of its automated dispense systems to run fundamental Pick & Place operations.
ETX Board with heat sink (9498 396 03996) for AX machine more information pls email Jasmine@qy-smt.com Part Number Description Part Number Description 5322 218 10804 DETECTOR, VACUUM 5322 218 11514 EPD 5322 218 10805 DETECTOR, COMPRESSER
Technical Library | 2020-07-08 20:05:59.0
There is a compelling need for functional testing of high-speed input/output signals on circuit boards ranging from 1 gigabit per second (Gbps) to several hundred Gbps. While manufacturing tests such as Automatic Optical Inspection (AOI) and In-Circuit Test (ICT) are useful in identifying catastrophic defects, most high-speed signals require more scrutiny for failure modes that arise due to high-speed conditions, such as jitter. Functional ATE is seldom fast enough to measure high-speed signals and interpret results automatically. Additionally, to measure these adverse effects it is necessary to have the tester connections very close to the unit under test (UUT) as lead wires connecting the instruments can distort the signal. The solution we describe here involves the use of a field programmable gate array (FPGA) to implement the test instrument called a synthetic instrument (SI). SIs can be designed using VHDL or Verilog descriptions and "synthesized" into an FPGA. A variety of general-purpose instruments, such as signal generators, voltmeters, waveform analyzers can thus be synthesized, but the FPGA approach need not be limited to instruments with traditional instrument equivalents. Rather, more complex and peculiar test functions that pertain to high-speed I/O applications, such as bit error rate tests, SerDes tests, even USB 3.0 (running at 5 Gbps) protocol tests can be programmed and synthesized within an FPGA. By using specific-purpose test mechanisms for high-speed I/O the test engineer can reduce test development time. The synthetic instruments as well as the tests themselves can find applications in several UUTs. In some cases, the same test can be reused without any alteration. For example, a USB 3.0 bus is ubiquitous, and a test aimed at fault detection and diagnoses can be used as part of the test of any UUT that uses this bus. Additionally, parts of the test set may be reused for testing another high-speed I/O. It is reasonable to utilize some of the test routines used in a USB 3.0 test, in the development of a USB 3.1 (running at 10 Gbps), even if the latter has substantial differences in protocol. Many of the SI developed for one protocol can be reused as is, while other SIs may need to undergo modifications before reuse. The modifications will likely take less time and effort than starting from scratch. This paper illustrates an example of high-speed I/O testing, generalizes failure modes that are likely to occur in high-speed I/O, and offers a strategy for testing them with SIs within FPGAs. This strategy offers several advantages besides reusability, including tester proximity to the UUT, test modularization, standardization approaching an ATE-agnostic test development process, overcoming physical limitations of general-purpose test instruments, and utilization of specific-purpose test instruments. Additionally, test instrument obsolescence can be overcome by upgrading to ever-faster and larger FPGAs without losing any previously developed design effort. With SIs and tests scalable and upward compatible, the test engineer need not start test development for high-speed I/O from scratch, which will substantially reduce time and effort.
http://www.gpd-global.com GPD Global expands the performance of its automated dispense systems to run fundamental Pick & Place operations. The same automated fluid dispensing machine is capable of dispensing fluids and also Pick & Place simple compo
http://www.gpd-global.com No drip no drool across a wide range of fluid viscosities (low-to-mid and low-to-high). No manual adjustment to compensate for pump variability. Truly Volumetric PCD Pumps for total control of dispensing fluids. Ability to
Career Center | Huntington Beach, California USA | Production
Responsibilities • We are looking for a full time self motivated team member • Develop and refine production processes (SMT and thru hole) • Train personnel to operate SMT line • Review and interpret customer contracts and quality standards. • P
Career Center | Irvine, California USA | Engineering,Technical Support
Act as a response center engineer to work with customers of Tecnomatix-Unicam products. Resolve problems over the telephone or on site as necessary. Travel to customer sites is required. Act as a local expert for Tecnomatix-Unicam product lines. Conf
Career Center | , | Engineering,Production,Technical Support
Experience 1992–Present IEC Electronics Newark, NY SMT Programmer SMT Machine Operator Built new programming system for IEC, Fuji Flexa from the ground up. Saved company several thousand dollars in revenue, per year by changing department to paper
Career Center | Ballston Spa, New York USA | Engineering,Maintenance,Production,Purchasing,Quality Control,Research and Development,Sales/Marketing,Technical Support
Qualifications / Skills: Maintain and repair X-Ray inspection equipment Maintain Surface Mount Manufacturing Systems Full DEK OEM equipment training Train Surface Mount Technology, Semiconductor, and Solar Photovoltaic operators and engineers Mainta
: 387 Description: Spectrometer Make: Solar Unicam; Type: Unicam 969 AA Spectrometer; Serial No 500558; Inventory number: 13952 with associated PC Make: Dell Type