Technical Library: qfn thermal pad (Page 1 of 30)

Void Reduction in Bottom Terminated Components Using Vacuum Assisted Reflow

Technical Library | 2019-07-10 23:36:14.0

Pockets of gas, or voids, trapped in the solder interface between discrete power management devices and circuit assemblies are, unfortunately, excellent insulators, or barriers to thermal conductivity. This resistance to heat flow reduces the electrical efficiency of these devices, reducing battery life and expected functional life time of electronic assemblies. There is also a corresponding increase in current density (as the area for current conduction is reduced) that generates additional heat, further leading to performance degradation.

Heller Industries Inc.

Key Advances in Void Reduction in the Reflow Process Using Multi-Stage Controlled Vacuum

Technical Library | 2020-01-28 00:23:58.0

This paper explores new advances in the reflow soldering process including vacuum technology and warpage mitigation systems. The first topic for discussion will be the implementation of a vacuum process directly in a conventional inline soldering system. The second topic presented is the mitigation of warpage on substrates or wafers.

Heller Industries Inc.

Thermal Residue Fingerprinting: A Revolutionary Approach to Develop a Selective Cleaning Solution

Technical Library | 2009-07-01 09:24:25.0

During the last 5 years, the processes to remove flux residues especially for lead-free and challenging geometries have demonstrated new cleaning obstacles which have to be overcome.i A new methodology has been recently developed to further increase the propensity for successful cleaning.ii At the core of this method is the thermal identification of the residue matrix. Thermal energy changes the physical state, i.e. transitions between liquid, solid and gas phases. By taking advantage of such specific information during phase transitions, the cleaning process can be tailored to such settings, which in turn increases the cleaning success significantly.

ZESTRON Americas

Advanced Solder Paste Dispensing

Technical Library | 2008-10-15 20:16:12.0

Solder paste dispensing is usually considered a slow process. Due to the speed advantages, screen printing is used to apply solder paste whenever possible. However, screen printing is not always an option. Leveraging the high speed of piezo drive technology opens the door to a broad range of solder paste dispensing applications. The ability to dispense dots under 300-μm diameter, even as small as 125 μm, enables BGA rework, small geometry deposits for miniaturized passive components, electrical connections in recessed cavities, and RF shield attach for handheld devices.


Conductive Adhesive Dispensing, Process Considerations

Technical Library | 1999-08-27 09:24:56.0

Dispensing conductive adhesives in an automated factory environment creates some special challenges. A robust production process starts with understanding the adhesives in their fluid state and which important parameters must be controlled. Developing this understanding requires experience with a large number of materials and valves over time. Common uses of conductive adhesives in surface mount applications, die attach applications, and gasketing are addressed. As vendors of dispensing equipment, the authors see a constant stream of such applications. Dispensing requirements, techniques, and equipment resulting from this experience are discussed. Guidelines for optimizing quality and speed are given.


Rework Challenges for Smart Phones and Tablets

Technical Library | 2015-04-23 18:48:18.0

Smart phones are complex, costly devices and therefore need to be reworked correctly the first time. In order to meet the ever-growing demand for performance, the complexity of mobile devices has increased immensely, with more than a 70% greater number of packages now found inside of them than just a few years ago. For instance, 1080P HD camera and video capabilities are now available on most high end smart phones or tablet computers, making their production more elaborate and expensive. The printed circuit boards for these devices are no longer considered disposable goods, and their bill of materials start from $150.00, with higher end smart phones going up to $238.00, and tablets well over $300.00.


Risk Mitigation in Hand Soldering

Technical Library | 2019-01-02 21:51:49.0

Failed solder joints remain a constant source of printed circuit board failure. Soldering is the bonding of metallic surfaces via an intermetallic compound (IMC). The interaction between thermal energy delivery, flux chemistry, and solder chemistry creates the solder bond or joint. Today, reliability relies on visual inspection; operator experience and skill, control of influencers e.g. tip geometry, tip temperature, and collection and analysis of process data. Each factor involved with the formation of the solder joint is an element of risk and can affect either throughput or repeatability. Mitigating this risk in hand soldering requires the identification of these factors and a means to address them.


Effective Qualification of Soldering Iron Performance Criteria

Technical Library | 2012-11-27 14:06:48.0

Quality managers and line supervisors are routinely tasked with the responsibility of ensuring that the hand soldering process is under control. The method most commonly used is to measure the idle tip temperature of the soldering station and to use this reading as a benchmark of system compliance. This method, although popular is now being seriously questioned by many industry professionals as being irrelevant in qualifying true system process control. This document aims to present a practical view of what factors are important for successful hand soldering and to suggest an alternative procedure for qualification that is simple, repeatable and directly related to the effectiveness of the soldering station.


Hand Soldering with Lead Free Alloys

Technical Library | 2018-02-22 10:56:36.0

As companies start to implement lead free soldering processes, hand soldering and associated techniques have been identified as key functions in the manufacturing process requiring additional research and development. Hand soldering tends to occur at the end of the process line where the circuit board has a high intrinsic value and so correct process control will have a significant affect on manufacturing costs and productivity.This paper discusses the fundamental aspects of the hand soldering process and discusses process adaptation requirements for successful lead free implementation.


Surface Mount Rework Techniques

Technical Library | 1999-05-09 12:51:38.0

This Technical Note outlines, step by step, the easiest ways to remove and replace surface mounted devices, using the lowest possible temperatures. This document discusses the following topics: Removal and replacement of discrete and passive components (capacitors, resistors, SOTs), Removal of two-sided components (SOICs, SOJs, TSOPs), Removal of quad components (PLCCs, QFPs), Replacement of quad components including fine-pitched devices.


  1 2 3 4 5 6 7 8 9 10 Next

qfn thermal pad searches for Companies, Equipment, Machines, Suppliers & Information