Used SMT Equipment: quants (1)

Vitronics Quants pro 6738Q2

Vitronics Quants pro 6738Q2

Used SMT Equipment | Soldering - Reflow

Reflow oven Vitronics Soltec Quants pro 6738Q2 built: 2000, with 6 heating zones top, 2 peak heating zones above and below, 2 cooling zones under, length processing zone 4180 mm, heating zone 3350 mm, control computer with LCD monitor, chain pint con

H.O. Lamberink

Industry News: quants (4)

Quant3D Launches Web Site and Online Store

Industry News | 2014-04-27 12:10:03.0

OK International is pleased to announce that Quant3D, its new brand focused on 3D printing has launched its Web site. The new site can be accessed via www.quant3d.com.

OK International

Quant 3D to Preview New Industrial Printer at EuroMold 2014

Industry News | 2014-11-18 18:02:28.0

Quant 3D, a division of OK International, will preview its new industrial 3D printer in stand 11.F103 at EuroMold 2014, scheduled to take place November 25-28, 2014 in Frankfurt, Germany. The new Q1000 Industrial 3D Printer is a high-performance, cost-effective 3D printing solution for industrial and large commercial applications.

OK International

Technical Library: quants (4)

Higher Defluxing Temperature and Low Standoff Component Cleaning - A Connection?

Technical Library | 2020-11-04 17:49:45.0

OEMs and CMs designing and building electronic assemblies for high reliability applications are typically faced with a decision to clean or not to clean the assembly. If ionic residues remain on the substrate surface, potential failure mechanisms, including dendritic growth by electrochemical migration reaction and leakage current, may result. These failures have been well documented. If a decision to clean substrates is made, there are numerous cleaning process options available. For defluxing applications, the most common systems are spray-in-air, employing either batch or inline cleaning equipment and an engineered aqueous based cleaning agent. Regardless of the type of cleaning process adopted, effective cleaning of post solder residue requires chemical, thermal and mechanical energies. The chemical energy is derived from the engineered cleaning agent; the thermal energy from the increased temperature of the cleaning agent, and the mechanical energy from the pump system employed within the cleaning equipment. The pump system, which includes spray pressure, spray bar configuration and nozzle selection, is optimized for the specific process to create an efficient cleaning system. As board density has increased and component standoff heights have decreased, cleaning processes are steadily challenged. Over time, cleaning agent formulations have advanced to match new solder paste developments, spray system configurations have improved, and wash temperatures (thermal energy) have been limited to a maximum of 160ºF. In most cases, this is due to thermal limitations of the materials used to build the polymer-based cleaning equipment. Building equipment out of stainless steel is an option, but one that may be cost prohibitive. Given the maximum allowable wash temperature, difficult cleaning applications are met by increasing the wash exposure time; including reducing the conveyor speed of inline cleaners or extending wash time in batch cleaners. Although this yields effective cleaning results, process productivity may be compromised. However, high temperature resistant polymer materials, capable of withstanding a 180°F wash temperature, are now available and can be used in cleaning equipment builds. For this study, the authors explored the potential for increasing cleaning process efficiency as a result of an increase in thermal energy due to the use of higher wash temperature. The cleaning equipment selected was an inline cleaner built with high temperature resistant polymer material. For the analysis, standard substrates were used. These were populated with numerous low standoff chip cap components and soldered with both no-clean tin-lead and lead-free solder pastes. Two aqueous based cleaning agents were selected, and multiple wash temperatures and wash exposure times were evaluated. Cleanliness assessments were made through visual analysis of under-component inspection, as well as localized extraction and Ion Chromatography in accordance with current IPC standards.

ZESTRON Americas

Evaluating Soldering Irons for Lead Free Assembly -A Quantitative Approach

Technical Library | 2006-09-06 15:25:43.0

Transition to lead free solder stations in electronics packaging has raised issues regarding process, metallurgy and reliability m assemblies. In regards to soldering, lead has been used for thousands of years in a wide range of applications. Conventional eutectic or near eutectic tin-lead solder compositions have been used for virtually all soldering applications in electronics assembly for the last 50 years, In the electronics assembly process, a majority of commercial rework applications and some low density board assembly processes require hand soldering stations (...) This paper describes an attempt to quantify both qualitative and quantitative data that can aid in the evaluation of lead free soldering irons.

T.J. Watson School of Engineering and Applied Science


quants searches for Companies, Equipment, Machines, Suppliers & Information

Sm t net
  1  
pcb assembly supplies

Real Time Process Control BREAKTHROUGH for Dispensing Industry.
MSD Dry Cabinets

Best Reflow Oven