Industry Directory | Consultant / Service Provider / Manufacturer / Research Institute / Laboratory / School
SMT & PCBA Laboratory Services, X-ray inspection, BGA rework, BGA Reballing, Solder Failure Analysis, SMT Assembly Process Validation, SMT Assembly Process Training & Consulting.
New Equipment | Rework & Repair Equipment
Inspection Mirror (SH-133S) The new inspection mirror meets clean room requirements yet is sufficiently economical for non-clean room applications. A quality tool for the technician but inexpensive enough to meet the budgetary requirement of modern
ProntoSELECTIVE-SOLDERING is used by electronic manufacturers to quickly program their Selective Soldering machines. ProntoSELECTIVE-SOLDERING helps program most popular Selective Soldering machines such as ACE Production Technologies, RPS Autom
Electronics Forum | Thu Apr 01 12:05:21 EST 2004 | babe
Heat guns scare me, hot air scares me too. Just the heck of it why not apply high temp paste to the center and eutectic 63/37 standard solder to the outside pads. The outside reflows first allowing proper seating of the component and with a proper pr
Electronics Forum | Mon Mar 08 09:03:17 EST 2004 | russ
Is this problem really related to the size of the BGA OR the size/thickness of the PCB? Would I be correct in assuming that your pre-heater is small in size? Usually a board warps like this when the ramp is to great at the localized area. the imme
Used SMT Equipment | Chipshooters / Chip Mounters
Samsung chip mounter SM-421 Advanced Flexible Mounter Using the vision system which is upgraded from the SM421 vision system, the SM421 can be applied to parts from 0603(0201) microchip to □22mm IC part through On-The-Fly reco
Used SMT Equipment | Chipshooters / Chip Mounters
Advanced Flexible Mounter Using the vision system which is upgraded from the SM421 vision system, the SM421 can be applied to parts from 0603(0201) microchip to 22mm IC part through On-The-Fly recognition. It also allows recognition of parts with
Industry News | 2003-06-04 09:19:23.0
With increasing demand for fine pitch placements and a growing amount of fast turnaround high-tech low-volume prototype work, Speedboard has invested in additional SMT/BGA placement/rework equipment.
Industry News | 2003-06-12 08:24:37.0
An adaptive tool prevents small and/or light components "lifting" or "floating" on printed circuit board assemblies during the wave solder process.
Parts & Supplies | General Purpose Equipment
The new inspection mirror meets clean room requirements yet is sufficiently economical for non-clean room applications. A quality tool for the technician but inexpensive enough to meet the budgetary requirement of modern manufacturing. /8" Mirror He
Parts & Supplies | Repair/Rework
The RocHard 1 MilProbe is a 0.3" long Micro-tip in a 4 3/8" long hex shape stainless steel handle. The Micro-tip is tapered to a one mil diameter tip for TAB, BGA, and other ultra fine pitch rework. The tip is either straight (SH-341) or 50? angled a
Technical Library | 2019-05-21 17:38:55.0
Last month we presented Flip Chip Rework.As promised, this month we follow up with attachment techniques. Flip chip assembly is a key technology for advanced packaging of microelectronic circuits. It allows attachment of a bare chip to a packaging substrate in a face-down configuration, with electrical connections between the chip and substrate via conducting “bumps.” Flip chip technology was first invented by IBM for mainframe computer application in the early 1960s. Semiconductor devices are mounted face down and electrically and mechanically connected to a substrate (Figure 1). IBM called this manufacturing process a C4 process (controlled collapse chip connection).
Technical Library | 2020-09-02 14:34:23.0
Atomic layer deposition (ALD) is a process of creating coatings on a molecular layer by layer basis. Using an iterated sequence of self-saturating deposition cycles that are self-terminating, a single layer can be deposited at a time, allowing for highly uniform films with complete conformality. The composition of the film typically used for coating printed wiring boards (PWBs) is a high alumina (Al2O3) sequential deposition of alumina and titania capped with a corrosion protective titanium aluminate layer, most notably ALD-Cap from Sundew Technologies, LLC. Rework is a process of restoring an electronics assembly to full functionality to prolong equipment life and reduce the amount of scrap. The process typically involves:
www.unisoft-cim.com/solder.htm - The ProntoSELECTIVE-SOLDERING module from Unisoft is used by electronics manufacturers to generate the necessary programs for automatic PCB Selective Soldering machines in minutes. ProntoSELECTIVE-SOLDERING helps prog
www.unisoft-cim.com/pcbtest.htm - In minutes the Unisoft ProntoTEST-FIXTURE software translates CAD & BOM files into real reference designators, netlists, X/Y component pin geometries, values, tolerances, part numbers, etc. This data is used by Test
Training Courses | | | PCB Rework and Hand Soldering Courses
The PCB rework and hand soldering courses courses cover techniques of rework and repair of PCBs, BGAs and other electronics assemblies, and teach fundamentals of soldering of electronics assemblies.
Training Courses | | | IPC-7711/7721 Trainer (CIT)
The Certified IPC-7711/7721 Trainer (CIT) courses recognize individuals as qualified trainers in the area of rework and repair of printed boards and electronic assemblies and prepares them to deliver Certified IPC-7711/7721 (CIS) training.
Career Center | Columbus, Ohio USA | Engineering,Management,Production,Quality Control,Research and Development,Technical Support
20 plus years of experience in a Electronics Manufacturing environment. Management experience on 1st and 2nd shift with groups up to 18 in a goverment contracted environment Experienced internal/lead auditor of ISO 9001 with years of audit experi
Career Center | Columbus, Ohio USA | Engineering,Management,Production,Quality Control,Research and Development,Technical Support
20 plus years of experience in a Electronics Manufacturing environment. Management experience on 1st and 2nd shift with groups up to 18 in a goverment contracted environment Experienced internal/lead auditor of ISO 9001 with years of audit experi
Article Return to Front Page Rework Management and Opti
SMT Express, Issue No. 6 - from SMTnet.com Volume 1, Issue No. 6 Monday, November 22, 1999 Featured Article Return to Front Page Rework Management and Optimization Learning how to manage the amount of time and money spent on rework can increase
| https://www.eptac.com/ask/75-barrel-fill-requirement-for-class-2-change-in-j-std-001-revision-f/
: Why did the IPC change the barrel fill requirement for Class 2 in J-STD-001 Revision F? Revision E allowed 50% when there was a thermal plane. Now, Rev. F states 75
| https://www.smtfactory.com/I-C-T-2019-Team-Building-id3290148.html
Router PCBA V-cutting Machine PCBA Coating Line Machine Belt Assembly Line X-ray / BGA SMT X-ray Machine BGA Rework Station Laser Making Machine SMT Peripheral Equipments Solutions LED Industry LED